kimchi & kraut

Passive House + Zero Net Energy + Permaculture Yard

Tag Archives: 475 High Performance Building Supply

WRB: Zip Sheathing (Air Sealing #6 )


Zip: Air Sealing the Seams and Penetrations

( Note: This post will concentrate on the Zip sheathing itself, as it relates to seams and penetrations. I’ll address how I sealed around openings for windows and doors, along with our attic access hatch through the Intello on the ceiling in separate, future blog posts.)

We used Zip sheathing as our WRB (water-resistant barrier — or sometimes it’s referred to as a weather-resistant barrier) based largely on Hammer and Hand projects,

and seeing it used on various jobs featured in Fine Homebuilding Magazine.

As the 7/16″ Zip sheathing went up, I taped most of the seams with Pro Clima’s  3″ Tescon Vana tape (available at 475 HPBS), but also their Contega tape (6″ wide), which I used mainly for outside corners and larger seams in the Zip (mainly where the horizontal seam in the Zip transitioned from the exterior walls of 2×6 framing to the roof trusses — shown in a photo later in this post).

My wife and daughter also cut up the Tescon Vana tape into small pieces in order to cover all the nail and screw holes in the Zip sheathing.

beast and eduardo taping nail holes

The Beast and Eduardo team up to tape the nail and screw holes on the lower sections of Zip sheathing around the house.

The nail holes were initially sealed with HF Sealant, also available from 475 HPBS, thus giving them double coverage — this was discussed earlier, here:

Framing (Air Sealing #2)

north side house garage gap long view

Northeast corner of the house where it meets the garage.

Our decision to use the Zip sheathing was also discussed earlier, here:

Wall Assembly

And here’s a good video discussing the Zip sheathing and its benefits (and its place in the evolution of building science):

If I had it to do over, I think I might be tempted to use 1/2″ exterior grade plywood as my sheathing (there are any number of WRB options these days). This would be sealed on the exterior side with either a liquid membrane, like Prosoco’s Cat 5, or a peel-n-stick tape like Henry’s Blue Skinor even another 475 HPBS product Solitex Mento 1000.

The Zip sheathing works, and the exterior green skin held up nicely during construction, even as it sat exposed for nearly 10 months after we fired our GC’s and struggled to keep the project moving forward. Nevertheless, it is little more than glorified OSB, which comes with certain inherent weaknesses.

Matt Risinger does an excellent job of delineating the cost/benefits of using either OSB or CDX plywood as a sheathing material:



Garage (at left) house (at right) connection. Gap will eventually be filled with 4″ of Roxul Comfortboard 80.



Closer view of this same garage – house connection. Flashing will cover the bottom of the Zip and then carry over the top of the Roxul that covers the foundation.



View of the north side of the house as Tescon Vana tape air seals the nail holes and the seams in the Zip sheathing.

View of the West facade with Tescon Vana tape, along with the black Contega tape at larger seams (e.g., where the walls meet the roof trusses) and outside corners.

west side being taped

West facade as taping proceeds.


taping north side before mechanicals : windows

Northwest corner of the house, transitioning from the Tescon Vana to the black Contega tape at the corner.


finishing up seams on west facade

Finishing up some of the final seams in the Zip on the West facade.

Once the Zip was fully installed, it was readily apparent that some of the seams, especially near the base of the first floor where a horizontal seam ran around the entire structure, would need to be tightened up.

Here’s a view looking down on one of these areas where the Zip sheathing did not sit flat against the framing members:

down Zip - out of alignment before 1x4's

Horizontal seam in Zip sheathing refusing to lie flat against the 2×6 framing members.

Using a 1×4 in each stud bay, I was able to pull the seam in the Zip sheathing together. It wasn’t always perfect, but the difference was visibly significant and in most areas well worth the effort.

Placing a 1×4 into position over the seam in the Zip, I would drive a couple of screws towards the exterior.

1x4 in study bay before HF

1×4 used to pull an unruly seam in the Zip sheathing together.


screw thru zip for 1x4 in stud bay

Screw from the interior poking outside as it initially gets the 1×4 in place.

Once securely attached from the interior, I went outside and drove several screws into the Zip, both above and below the seam in the Zip, to pull the seam tight to the 1×4. At that point, I could go back inside and remove the two screws that were driven towards the exterior.

In addition to air sealing the exterior side of the Zip sheathing, I also invested some time in air sealing the interior side of the Zip as well. Below is a long view of several stud bays with 1×4’s installed, but before air sealing gaps around the 1×4’s and lower areas of the stud bays with HF Sealant.

stud bays w: 1x4's, before HF

Long view after applying the HF Sealant:

ceiling walls - HF Sealant

Close up of the interior side of the Zip sheathing meeting a 2×6 framing member in a stud bay after applying a thick bead of HF Sealant:

thick bead HF sealant in stud bay

Close up of lower area of a stud bay after air sealing with the HF Sealant (it transitions from a light to darker green as it dries):

stud bay w: 1x4 and HF sealant

1×4 installed and HF sealant applied to all gaps and screw/nail holes in the stud bay.

I held off on using the HF Sealant at the wall sill plate/subfloor connection until just prior to installing the Intello on the walls since this area constantly attracts dirt and debris.

Sealing on the interior side with HF Sealant, even between vertical framing members, means that even if there are any weaknesses in either the Zip sheathing or the Tescon Vana tape at these points, air won’t find an easy way in, since it will be blocked from the interior side as well (there won’t be a difference in air pressure to help the outdoor air make its way indoors).

This kind of redundancy in air sealing should give the house long-term protection against air leaks, thereby aiding the long-term durability of the structure, as well as making it a much more comfortable environment to live in.

interior walls sealed w: HF sealant

Using HF Sealant between vertical framing members.

I also spent some time on the roof trusses, sealing around nails, the top plates of the exterior walls, and the many Zip-framing member connections in what will eventually be the attic.

sitting on roof trusses sealing

Sealing around fasteners and framing in the attic with HF Sealant.

This had less to do with air sealing and more to do with preventing any potential water intrusion since this area is technically above our ceiling air barrier (the Intello), which is detailed here:

Ceiling Details (Air Sealing #4)




Inventory of Penetrations through the Zip Air Barrier

I made a mock wall assembly before construction began, which I discussed here:

Wall Assembly

This proved helpful when explaining to the various subs how to help me protect the air barrier — especially when it came time to drill holes through the Zip sheathing. Of particular importance was making holes closer to the center of a stud bay, as opposed to hugging a corner or side of one of the 2×6 framing members. A hole cut too close to a stud or a roof truss is much harder to properly air seal.


Interior side of our mock wall assembly, showing how all penetrations through the Zip should be in the middle of our framing members. Our original plumber was the only trade that managed to screw this up (it’s no coincidence that he was also the only sub that we had to fire).

In effect, any time a sub had to make a penetration through the air barrier we discussed the details, and once the cut was made I immediately air sealed the penetration both on the exterior and interior side.

By sealing each hole in the Zip on both sides, again I hope it ensures the long-term durability of the overall structure. The main argument for this strategy assumes the exterior side of the sheathing will face more extreme temperatures, and fluctuations in humidity, and presumably even wind-drive rain if/when it gets past the siding and 4″ of Roxul insulation, putting it at greater risk of failure (especially in the long term). By taking the time to air seal the interior side, it just gives the overall air barrier, and therefore the structure, a better chance at avoiding air and water intrusion (that’s the goal anyway).

For air sealing I used a mix of tapes, HF sealant (later even some Prosoco products), EPDM Roflex gaskets, and duct seal.

The penetrations for electric service were my first go at using the Roflex gaskets.

John & Donny installing meter

John and Danny, from Chicago Electric, installing the electric meter.

The smaller diameter Roflex gasket comes with its own Tescon Vana tape, which makes installation straightforward.

close up meter thru Zip w: TVana gaskets

Electric meter with Tescon Vana – Roflex gaskets installed.


meter - hole, t. vana prior to appl.

Exterior view of electric Meter air sealed with gaskets and Tescon Vana tape:

electric meter close up gasket : t. vana

Once sealed on the exterior side, I went inside to seal the penetrations for a second time.

meter to panel - interior

Air sealing the electric meter on the interior side.

It was a big moment when the electric panel went in.

main panel in - progress

The house is ready for power.

The installation of our solar panels required air sealing two penetrations — one through the Intello on the ceiling on the inside of the structure, along with one exterior penetration through the Zip:





Details regarding the installation of our Solar array can be found here:

Solar on the Roof

corrected solar on:off

Solar disconnect (on/off) with its Tescon Vana gasket.

We also had two frost-free hose bibs, or sill cocks installed, which also required gaskets on the exterior and interior sides of the Zip sheathing.

hosebib w: gasket

Frost free hose bib with gasket.

One of the big advantages a Roflex gasket has over using a sealant like the green HF Sealant, or Prosoco’s Joint and Seam, is the pipe can be moved in and out even after air sealing, which is especially helpful for installing siding later.

We left the sill cocks loose (unconnected inside the house), allowing the siding guys to adjust in and out for a more precise fit of the charred cedar siding.

Below is an example of what conduit through the Zip sheathing looks like before it gets a gasket and tape:

exterior light conduit before gasket

Penetration for conduit before gasket.

And here’s the conduit after the gasket and tape.

gasket for exterior light

Conduit after gasket.

Note the extended length of the conduit, anticipating our 4″ of Roxul covering the Zip, 2-layers of furring strips (vertical then horizontal — for vertically oriented siding), and the eventual charred cedar siding.

The photo below shows the penetrations, along with multiple lines of conduit, for our eventual ductless mini-split Mitsubishi heat pump system. The empty hole will be our disconnect for the heat pump. I’ll go into the details of our ductless mini-split system in a future post.

conduit for heat pumps

Penetrations for our Mitsubishi heat pump system.

Same series of conduit pipes after gaskets and being connected to the compressor outside:

heat pump electric w: t. vana before disconnect

In addition to the conduit for electrical hook-up, the Mitsubishi heat pump system required a separate penetration for running the refrigerant lines to the compressor.

hole in Zip for heat pump pvc

Hole cut for the heat pump refrigerant lines.

After discussing it with Mike from Compass Heating and Air, who did our ductless mini-split installation, we decided to use a 4″ section of PVC plumbing pipe as our “conduit” for running the refrigerant lines from the interior of the structure to the outside.

heat pump - pvc pipe in hole for lines

4″ PVC plumbing pipe for the refrigerant lines.

After the PVC was passed through the hole in the Zip, we added a 2×4 underneath it to give it some added stability, along with the usual gasket and tape for air sealing around the PVC pipe.

heat pump - int side - pvc, gasket, 2x4

Before applying Tescon Vana around the Roflex gasket.

Once the refrigerant lines were passed through the PVC pipe, it was clear that some additional air sealing was required.

gaps around pvc lines before duct seal

PVC pipe with refrigerant lines installed.

I filled the gaps around the refrigerant lines from the interior and exterior sides with duct seal. Before stuffing in the duct seal at either side of the PVC pipe, I added bits of Roxul Comfortboard 80 into the pipe to try and give added R-value to the interior of the PVC pipe (hoping to prevent any possible condensation from forming inside the pipe).

duct seal label

A real life saver when it comes to air sealing. Readily available at big box stores, or online at Amazon.

Duct seal proved especially helpful at air sealing multiple weak points in the structure —areas that would’ve been difficult or impossible to air seal with just tape, gaskets, or sealants.

heat pump pvc w: duct seal close up interior

Using duct seal to block off air from the interior side.


heat pump pvc w: gasket before t. vana close up

Another view of the PVC pipe with duct seal.


heat pump refrigerant lines - int. leaving basement

The refrigerant lines transitioning from the basement ceiling to the PVC pipe before leaving the structure.

Once the interior was taken care of, I was able to address the exterior side of the PVC pipe:

heat pump lines before tape after duct seal

Exterior view of the PVC pipe with heat pump refrigerant lines exiting the structure, being air sealed with a Roflex gasket and duct seal inside the pipe.

Again, note that the PVC pipe is extended out in preparation for the layers of exterior insulation, furring strips, and siding.

heat pump lines leaving house - sealed

Same area after completing the air sealing with Tescon Vana tape.

And here’s a view of the same area after the siding was installed (I’ll go into the many details regarding the installation of the exterior insulation, furring strips, and siding in a later post).

Heat pump lines w: duct seal and siding

Air sealing for the refrigerant lines complete after the siding is installed.

Additional areas where the duct seal proved to be invaluable:

close up exterior outlet box w: duct seal

Exterior electrical boxes for lights and outlets.

Conduit for the water meter in the basement (only the interior is shown below, but the conduit was air sealed with duct seal on the exterior end as well):




And here’s the same conduit for the water meter as it leaves the house on the first floor:

conduit for water meter sealed w: tape:gasket

Conduit for the water meter, air sealed on both sides of the Zip with the Roflex/Tescon Vana gasket.

I also had to address the disconnect boxes for our solar array and our heat pump. For instance, here’s our solar disconnect box when it’s open:

solar disconnect before removing

And here it is after removing the pull out switch, revealing an air leak:

solar disconnect before duct seal

Close up of the conduit:

close up solar disconnect before duct seal

An even closer look:

close up penetration in solar box before duct seal

And here it is after being air sealed with the duct seal:

close up solar box after duct seal

I did the same air sealing for the Mitsubishi heat pump disconnect box:

heat pump box before removing

Close up of the conduit sealed with the duct seal:

close up penetration in heat pump box w: duct seal

During my initial blower door test (more on that later), some air movement around the main panel in the basement was detected, so when the electrician came back we added duct seal to the main pipe entering the house (it had already been sealed from the exterior side with duct seal):

main panel - interior - duct seal

Close up view of the main panel from the interior where lines first enter the structure.

Besides the penetrations in the Zip sheathing, there were other penetrations through the Intello (our air barrier on the ceiling) that had to be addressed as well. These areas were air sealed with the same set of products as the Zip.

For example, in addition to the conduit for solar through the Intello, we also had to air seal conduit for electric service to the attic (for a light and switch in the attic), in addition to the the penetrations for radon and plumbing waste vents, some of which are shown below:

plumbing vent thru Intello gasket:t. vana

Plumbing waste vent going into the attic.

Another view of this vent pipe after air sealing, this time from below:

sealed plumbing vent from below

Here is one of the vents that our first, incompetent plumber installed too close to one of the 2×6’s used to establish our service core.

plumbing vent installed too close to 2x6

Installed this close to framing makes air sealing the vent needlessly complicated and frustrating.

Here’s the same area after applying the Tescon Vana tape:

plumbing vent too close to 2x6 sealed w: tape

Below is another vent pipe incorrectly installed too close to a 2×6. This one was even more challenging to air seal properly. After the gasket and Tescon Vana, I added the green HF sealant as insurance against air leaks, both for now and in the future.

vent too close w: sealant too

We also had to air seal the penetrations for our Zehnder Comfo-Air 350 ERV ventilation unit. I’ll go into the details of the actual installation later, but here are some photos of the penetrations through the Zip sheathing and how we addressed making them air tight.

ext - comfo pipe going thru zip into basement

First section of Comfo pipe going through the Zip sheathing.


Zehnder tube exiting w: gasket

The gray Zehnder Comfo pipe (for supply air stream) exiting the structure with a Roflex gasket.


Zehnder pipe sealed w: gasket and tape

Closer view of the Comfo pipe air sealed with a gasket and Tescon Vana tape.


close up Zehnder Comfo Pipe w: gasket and t. vana

An even closer view of this same area where pipe meets gasket and tape.

We followed the same process — Roflex gasket, Tescon Vana tape — for the exterior side of the Zehnder Comfo pipe.

ext Zehnder gasket : t. vana

Zehnder Comfo pipe installed, air sealed, and ready for commissioning.

And here’s a picture of both supply and exhaust pipes for the Zehnder.

Zehnder exhaust and supply pipes ext fully sealed

Supply pipe in the background, exhaust in the foreground. The garbage bags keep out weather and animals until after the siding is up and the final covers can be installed.

During my initial blower door test some air movement around the sump pit was detected.

sump pit air sealed

Sump pit lid sealed with duct seal, Roflex gasket with Tescon Vana, and the seam between the pit and lid sealed with Prosoco Air Dam.

The sump pump discharge pipe also needed to be air sealed on both sides of the Zip.

sump discharge pipe w: gasket and joint and seam

Sump discharge pipe sealed first with Prosoco Joint and Seam, then a Roflex gasket, before applying Tescon Vana tape around the gasket.

Some air movement around the ejector pit was also detected, so I used duct seal to try and block it.

ejector pit air sealed with duct seal

Ejector pit air sealed with duct seal.

For low voltage — in our case, a cable TV/Internet connection — we found a utility box at Lowe’s (also available at Home Depot and Amazon), and combined it with conduit to transition from the exterior to the interior. The diameter of the conduit is large enough to allow wires for other utilities/services to pass through as well, if necessary, in the future.

cable box

Cable box installed after the siding went up.

An engineer from Comcast-Xfinity visited the site back in the summer, and he gave me the go-ahead for using this box/conduit set-up.

close up exterior of closed cable box

Closer view of the cable box.


cable box ext without cover

The cable wire exiting the house through the conduit, which is air sealed with duct seal.


cable wire int. basement

Cable wire on the interior of the house exiting through the Roxul insulation and Zip sheathing via the conduit and then air sealed from the interior with duct seal.

Even the wire for the doorbell was sealed with a gasket and tape.

doorbell gasket and tape

When the weather warmed up I was able to experiment with the Prosoco R-Guard series of products (note the 3/4″ plywood door buck treated with Joint and Seam and Fast Flash). I’ll go into that more when I discuss prepping for the windows and doors later.


close up of doorbell gasket

A closer view of the doorbell gasket.

Air sealing the penetrations was challenging at times, but also a lot of fun — always keeping in mind the goal of meeting the Passive House standard of 0.6 ACH for our blower door test.

Convinced of the connection between air tightness and the durability of a structure — not to mention the impact air tightness has on heating and cooling loads (i.e., monthly utility bills) —I wanted to see just how air tight I could get the house.

Hopefully this inventory of penetrations will prove helpful to someone in the planning stages of their own “air tight” build. It always helps to be able to see how other people do things — in particular, the strategies they employ and the specific products they use. Seeing these real world examples of air sealing around the many penetrations in a structure will hopefully give others the confidence to come up with their own plan of attack for building an air tight structure.

Ceiling Details (Air Sealing #4)


Installing Intello

We thought about using the Zip sheathing as our air barrier on the ceiling, attaching it to the bottom of the roof trusses, something I had seen on other builds, but after learning about Intello we decided to use that instead:



Floris Keverling Buisman, from 475 High Performance Buidling Supply, did our WUFI analysis for us, and he suggested the Intello would be a better fit for our project. The Intello is a smart vapor retarder, so it can expand and contract when it’s needed, and it’s obviously less physically demanding to install than the Zip sheathing.

Once the air sealing was complete around the top of our outside perimeter walls, and the insulation chutes had been installed, we were almost ready for the Intello. At the gable ends of the house, one last detail needed to be put in place, circled in red in the picture below:

2x6 on its side

2×6 on its side, circled in red.

By adding this 2×6 on its side, which is in the same plane as the bottom of the roof trusses, it makes it possible to carry the Intello over the transition from the ceiling (under the roof trusses) to the walls (top plates). This is one of those details that is hard to “see” when in the planning, more abstract, and two dimensional phase of designing a structure.

another angle of 2x6 on side

Another view of the 2×6 lying flat in the same plane as the bottom of the roof truss (far left).

Once the trusses were placed on the top of the walls and you start imagining how the Intello will be attached to the ceiling, it becomes much more obvious that something in this space at the gable ends of the house is needed in order to accomplish the transition from the ceiling to the walls.

long view w wdw to front door framing

Marking progress: Ceiling ready for the Intello.

After reading about so many other projects that utilized Intello, it was exciting to unwrap the first box.

unwrapping first box of Intello

Big day: opening the first box of Intello.

The directions are pretty straightforward, and the product is relatively easy to install, as long as you don’t have to do it alone.

Intello instructions

Reading through the instructions one last time before starting.

I didn’t get a chance to touch and feel the product before ordering (always fun to do with any new product), so here are some close-ups of the Intello to give you some sense of what it’s like:

Intello close up front side 2

Front: shiny side of the Intello — this side will be facing the living space.

I was curious about its strength and tried to tear it with various objects, including the cut ends of 2×4’s and the brackets we eventually used to help establish our service core. The material is surprisingly tear resistant, but a utility knife, or a stray sharp edge will cut through it (as our first plumber proved to me with his careless actions — a story for another post).

close up Intello back side

Back: matte side of the Intello — this side will be facing the attic.

Having never used the Intello before, I decided to start small and began by experimenting with it in a corner. Getting the corners fully covered while getting the material to sit flat before applying the blue Tescon Vana tape proved to be the most challenging part of using the Intello.

experimenting w: Intello in corner w: chutes above

Starting in a corner to get a feel for how the material will work.

Here’s two more pictures of the flat 2×6 helping to make the transition from the ceiling to the wall:

In order to attach the Intello to the bottom of the roof trusses, we used the staple gun shown below. Loading it is kind of counter-intuitive (online reviews complain about it not working out of the box, but my guess is — like me — they were trying to load it improperly), but once I figured it out, it ended up working really well, almost never jamming, and it’s very comfortable to hold because it’s so light weight. It should work with any standard air compressor. It was available on Amazon, and in Menards, a local big box store here in the Chicago suburbs.

staple gun

The staple gun we used to attach the Intello to the underside of the roof trusses.

Think you know how to load it?

side view of open staple gun

Staple gun ready for loading.

Guess again.

Instead of loading from the bottom, like all the finish nailers I’ve ever used, the staples load higher up, where the staples exit. And yes, there was quite a bit of swearing as I made the transition from “What the…” to “Ohhhh, now I get it…”.

It didn’t help that there were virtually no instructions on its use, apart from a tiny black sticker with an arrow pointing to where to load it (which, of course, I only noticed after figuring this out).

staple gun open w: staples

Loading the staple gun.

We started with these staples:

close up Arrow staples

But we ended up going with these instead:

close up heavy duty Arrow staples

They seemed to grab better (presumably the sharp ends make a difference), and they sit flatter on a more consistent basis (less time having to go back, or stop, to hammer home proud staples flat).

stapling Intello to ceiling

As we rolled out the Intello, it took some practice to get it to sit taught and flat before stapling.

The dotted lines near the edges of the Intello help you keep the rows straight as you overlap two sheets and progress from one row to the next. The lines also make it easier to maintain a straight line with the Tescon Vana tape (don’t ask me when I realized this latter detail — too embarrassing to admit).

taping Intello along dotted line

Follow the dotted line.

We checked our initial row from above in the attic:

first row of Intello from attic

View from the attic as the first row is installed.

Working our way through the interior walls, especially the bathrooms, was more time consuming and took more effort (I grew to hate those interior bathroom walls — first the Intello, then the service core details described below), but once we were out in the open, the Intello is fairly easy to install.

Intello covering ceiling, chutes in bg

First three rows of Intello as they approach the basement stairwell. Note the insulation chutes in the b.g. in the attic — they took up so much time and effort, and now they slowly disappear (just like most important aspects of infrastructure).


northwest corner of air sealed attic w: Intello

View of the Intello from a corner of the attic — note the 2×6, far left, lying flat, that helps the Intello transition from the ceiling to the top of the walls.


Intello from attic at outside corner

Another view of the Intello from the attic after installation.

As Eduardo and Jesus rolled out sections of the Intello, I followed, pulling on the Intello a little to help make it sit tight and flat, before stapling.

Eduardo and Jesus helping me put up Intello on ceiling

Eduardo and Jesus giving me a hand installing the Intello.

There were a couple of sections, some of the first ones we installed, that I managed to wrinkle (one, in particular, became problematic during our first blower door test — and, of course, it was in a tight spot around the bathroom shower area), but overall, the installation of the Intello went pretty well. Like most things you do for the first time, we got comfortable and good at it just as we were finishing up.

Eduardo Jesus and full moon night sky in b.g.

Eduardo and Jesus helping me finish up the main areas as a full moon makes the night sky glow outside in the background. It was a long day (longer still for Eduardo since Jesus was talkin’ trash and nonsense all day — they’re football teammates — needless to say, Eduardo has the patience of a saint).


Intello from attic w: insulation chutes in bg

View of the Intello from the attic — offering up its 2001: A Space Odyssey glow.

After learning about a project on the 475HPBS website…

Masonry Retrofit


… we decided to use the Tescon Vana tape to cover the staples, as well as all the seams, in the Intello. I have no idea what actual impact covering the staples has on air tightness, but visually as you tape over the staples you can see how, if nothing else, it will help the staples resist pulling out under pressure from the eventual blown-in cellulose in the attic.

Even as the build progresses, it’s interesting how details like this pop up, making building “green” a never-ending process of learning something new — someone’s always coming up with a new product or a new way to do things better, faster, or less complicated — which makes the process itself very exciting.

OB applying tape

OB — the Palatine High School legend — the man, the myth, helps me tape over the seams and staples in the Intello. One of the many jobs he’s been kind enough to help me get done. We’d be so far behind schedule without all of his help.


on plank

View from above what will be the basement stairwell while installing the Intello on the ceiling.


installing Intello on the ceiling around the basement opening

Almost finished installing the Intello — saved the hardest part for last.

This was a nice moment, being able to look back and see the Intello completely installed. It’s almost a shame that we have to cover it with drywall.

Intello on ceiling long view

Intello installed and taped.



2×6 Service Core

A design goal for the ceiling was to keep mechanicals, like HVAC and electric, on the conditioned side of the ceiling air barrier. By doing this, we avoid having to insulate any ductwork for HVAC, or air sealing and insulating around ceiling lights. In effect, we completely isolate the attic, making its sole purpose (apart from ventilating our “cold roof” assembly) holding our blown-in cellulose insulation (this set-up makes it much easier to air seal the ceiling and get the insulation right — at least based on the projects I’ve read about). In order to do this, we created a service chase, or service core, with 2×6’s:

service chase w: first couple of 2x6's

First couple of 2×6’s going in.

In addition to serving as a space to safely pass mechanicals through, the only other job for the 2×6’s is to hold up the ceiling drywall. The roof trusses, directly above each 2×6, are still carrying the load of the roof and stabilizing the perimeter walls.

Simpson L-Bracket w: fasteners

Simpson bracket and fasteners we used to attach the 2×6’s to the underside of the trusses.

Here’s what the 2×6’s looked like with their brackets once everything was installed.

close up service chase w: bracket-screws

Service core 2×6 with bracket and Simpson SDS bolts.

OB and my wife were invaluable, as they helped me cut and install all the 2×6’s.

We installed the brackets first, before raising up each individual 2×6 to fit against the brackets.

jesus helping me install 2x6's

Jesus helping me install the 2×6’s.

Since the brackets were directly attached and under a roof truss, we were able to keep the 2×6’s fairly straight, even when the board itself was less than perfectly straight.

service chase w: just brackets

Brackets installed before the 2×6’s go up.

A feisty Robin kept trying to set up a nest on our partition wall (our windows and doors aren’t in yet). Apparently she believed we had created an elaborate bird house just for her. It took almost a week before she finally gave up — but not before starting multiple nests in multiple spots along the wall.

bird nest

Robin making one of her many attempts at a nest on our partition wall.

Along the outside walls, at the top of the wall assembly, there was a gap that we utilized for maintaining continuous insulation. This meant there will be no break in our thermal layer going from the blown-in cellulose insulation in the attic to the monolithic layer of Roxul Comfortboard 80 (2″ + 2″) that will be on the exterior side of the Zip sheathing.

trusses - Intello - Roxul

Adding Roxul at the top of our wall.


layer of Roxul at top of outside wall

Close up of the Roxul going in on top of the top plates.


Intello - Roxul - wall

Another view after the Roxul has been installed.


long view from west window w: service core complete

Marking further progress: Intello and 2×6’s installed.

Once the 2×6’s were up, we had to install our pieces of 1×4 in order to prevent the 24″ of blown-in cellulose that will be going into the attic from causing the Intello to sag.

The plans called for the 1×4’s to be installed right after the Intello, but before the 2×6’s, which would have been a lot easier and quicker, but, unfortunately, the GC’s we fired installed the interior walls too high, making this impossible.

Here’s what it should’ve looked like if we could’ve done Intello and then the 1×4’s (photos courtesy of 475 HPBS) before installing the 2×6 service core:

Having no choice but to methodically cut each 1×4 to fit between each set of 2×6’s, OB was nice enough to help me get it done.

close up of partition wall w: service core and 1x4 cross battens

Installing the 1×4’s between the 2×6’s began with some experimentation:

service core w: cross battens and L-brackets

Using L-brackets at first —  it proved too time consuming and expensive.

After experimenting with a finish nailer (too easy to miss and penetrate the Intello), we eventually settled on Deckmate screws. It was definitely a laborious process, but eventually we got into a rhythm and got it done, although we wouldn’t recommend doing it this way — way too time consuming.

ceiling w: 1x4 battens

Completing our service core.

We tried to keep the 1×4’s about 16″ apart, which should prevent any significant sagging in the blown-in cellulose from occurring (I’ll post photos once the cellulose has been put in the attic).

A lot of blood, sweat, and tears have gone into completing this house…

Here’s some proof:

screw got me

A decking screw got me.

In trying to avoid puncturing the Intello, I would hold a couple of fingers on the back side of the 2×6, feeling for any screws that would come through on a bad angle. A couple of times I drove a screw too quickly and paid the price.

looking up at Intello and service core from basement

View of the service core from the basement. Installing the 2×6’s and the 1×4’s also required walking the plank a few more times.


installing ceiling w: OB

OB making my life easier as I work on the plank installing the 1×4’s.




Maintaining the Intello After Installation

Unfortunately, there was a delay in getting shingles on our roof, due in large part to our first, disorganized plumber (again, more on this later). Consequently, we were in the awkward position of having our ceiling air barrier and service core all set up, but every time it rained we still had a leaking roof. In most areas, it wasn’t a big deal, but in about a dozen spots rain would collect and, if heavy enough, it would bulge the Intello as the Intello carried the weight of the captured water. To relieve, and ultimately to avoid, this pressure, I cut small slits in the Intello where the rain would consistently collect.

small hole in Intello for rain before shingles

Slit in the Intello to allow rain water to fall through, marked with a red marker for easy identification later.

Once the shingles were finally on, I went back and found all of these slits and taped over them with the Tescon Vana.

Tescon Vana covering hole in Intello

Hole in the Intello covered and air sealed with the Tescon Vana tape.

We also found a couple of weak spots in the Intello as we installed it, and even later, during the installation of the service core. These spots were marked as well, and they, too, got covered with the Tescon Vana tape just for added insurance against air leakage.

imperfection in the Intello marked for Tescon Vana

Weak spot, or imperfection, in the Intello. This got covered with Tescon Vana as well.

After having to fire our GC’s, we couldn’t have kept the project going without the help of family and friends. As awful as some aspects of the build have been, it’s been heartwarming to find people willing to help us see the project through to the end (much more on this later).

2 Cheshire Cats

Couple of Cheshire cats — clearly up to no good — helping us to keep the job site clean.


Framing (Air Sealing #2)



In a conventionally built home, mudsills are typically an area of significant air leakage (if you’ve ever seen sill sealer — a thin layer of foam normally used to address this lumber-concrete connection — under an actual mudsill, you can visibly see just how poorly it performs).

In contrast, after reading about various strategies employed to reach the Passive House standard of 0.6 ACH for air tightness, I decided to use the approach developed by architect Steve Baczek specifically for mudsills.  There is an excellent article in Fine Homebuilding magazine that describes the details, and there is a companion series of videos available on Green Building Advisor (after the first video, membership is required, but it’s well worth it for this series of videos, as well as all the other information available on GBA).

We didn’t use the layer of poly, or the termite shield, but the remaining details we followed fairly closely. And we did make one product substitution — instead of using the Tremco acoustical sealant, we decided to go with the Contega HF sealant (less messy, lower VOC’s, and skins over and firms up enough to apply the Pro Clima tapes, all while remaining permanently flexible like the Tremco product —  these products are available at


Billy and Phil setting up chalk lines for the mudsills.



Nils applying a thick, continuous bead of Contega HF sealant, including around the bolts, before the 2×6 pressure treated sill plate gets installed with a BG65 gasket underneath.



BG65 gasket from Conservation Technology stapled to the bottom of a scrap piece of sill plate.



BG65 gasket rolled up in the box it shipped in.

Sammy and Billy stapling the BG65 gasket to the sill plates before installation:



Mudsill installed with some squeeze out of the sealant.

Installing the sealant on the mudsill (interior/exterior edges, seams, and bolts/nuts/washers) required some gymnastics:



In theory, she’s helping me.



Mudsill after installation: sealant covering sill plate – BG65 gasket – concrete connection, with seams filled.

Once again, based on Steve Baczek’s design — going from exterior to interior — here is our Mudsill Air Sealing Approach:

  • Bead of sealant on the exterior side of the 2×6/foundation connection
  • BG65 gasket under the sill plate — along with a thick bead of sealant under the gasket and sill plate (including around bolts)
  • Bead of sealant on the interior side of the 2×6/foundation connection
  • And then, finally, a taped connection on the interior side of the 2×6/foundation connection as a last line of defense against air infiltration (which I’ll complete once all the trades go through the interior of the house).

The approach assumes I will make mistakes at certain points with each layer of air sealing, so I’m counting on these layers of redundancy to protect me from myself. Again, this is the first time I’ve ever done this, so the theory is that even if I make a mistake in one area, it’s unlikely that I will make a mistake in exactly the same spot with successive layers of air sealing.

Obviously I’m trying to do my best with each layer, but I like the idea of added layers of protection (a Passive House obsession), especially when accounting for the long-term life of the structure. Even if each layer could be installed perfectly, presumably each layer will fail eventually at different times and in different places (hopefully 50-100 years from now if the accelerated aging studies are accurate), so hopefully these layers of redundancy will help maintain significant air tightness far longer than if I chose to use fewer layers. Plus, I’m enjoying sealing everything up, so I don’t mind the process, which always helps.

For larger gaps (not just for mudsills, but anywhere in the building envelope), roughly 3/8″ inch or larger, I am utilizing backer rod to help fill the gap before applying sealant.

This is what it looks like:


The backer rod (readily available at any hardware store) makes life easier for caulks and sealants — less stress on the connection between materials as the inevitable expansion and contraction occurs in the gap.

Hammer and Hand’s Best Practices Manual has the best explanation for their use that I’ve come across:

“While the humble sealant joint may be uncelebrated, it is vital to building durability and longevity. Proper installation is key to sealant joint integrity and function throughout a life of expansion and compression, wetting and drying, exposure, and temperature fluctuation.

Note: Because sealants are just as good at keeping moisture in as they are in keeping it out, placing a bead of caulk in the wrong location can result in moisture accumulation, mold and rot, envelope failure, and hundreds of thousands of dollars in repair and remediation. If we know anything, we know that building envelopes will get wet – the question is, “where will the water go?” Make sure you know the answer throughout construction, especially as you seal joints…


Diagram courtesy of Hammer and Hand’s Best Practices Manual.

… Joint Rule of Thumb: Sealant should be hourglass-shaped and width should be twice depth (shown in diagram).
Backer rod diameter should be 25% larger than the joint to be filled.
Joint size should be 4x the expected amount of movement (usually about 1/2” of space on all sides of the window casement).
Ideal joints are within a range of 1/4” at minimum and 1/2” at maximum. Joints outside this range require special design and installation.
Always use the right tool: sealant is not caulk and should never be tooled with a finger (saliva interferes with bond).
Substrates need to be clean, dry, and properly prepared (primer if necessary).
When dealing with thermally sensitive materials, apply sealant under average temperature conditions because joints expand and contract with changes in temperature…”


Example: Piece of backer rod being inserted into gap between header and 2×6.



It’s not visible, but the wood-concrete connection at the side wall has a piece of backer rod embedded between the two materials, making it easier for the sealant to bridge the gap over the long term.



Air Sealing: Rim Joist – Floor Joist – Mudsill Connections


Billy and Johnny installing the floor joists.

Since there was time between completion of the rim joist/floor joist installation and the installation of the sub flooring (a weekend), I took the opportunity to seal up all the visible connections. Once the subfloor goes in, these connections are still accessible from inside the basement, but the space to work in would be really cramped and uncomfortable (at least I thought so).


Rim joist – floor joist – mudsill connections prior to sealant being applied.

The same areas after applying the sealant:

More gymnastics required while applying the Contega HF sealant:

I found the silver Newborn sausage gun (photo below) worked great for thick beads under the mudsills, but the blue gun worked even better for all other seams. Because the blue gun utilizes disposable tips, it was easy to cut the tip to exactly the size I needed, thus using (wasting?) less material (and hopefully saving a little bit of money). An added benefit of the disposable tips is less time required for clean up at the end of the day (always a good thing). Both guns work great, and appear to be really well-made, although I would probably only buy the silver one again if I consistently needed a fat bead of sealant.


Newborn sausage guns I found on Amazon. The blue one works great for thin beads, the silver for thicker beads (e.g. under mudsills).

In the photos below, I filled larger gaps with either backer rod, or in the case of the largest gap, bits of pulled apart Roxul Comfortboard 80, before applying the sealant. Since this is the first time I’ve done this, these are the kind of connections that I failed to anticipate beforehand. They are definitely worth planning for.

The temptation is to just fill these kinds of voids with sealant, but for the long-term durability of the connection backer rod or some kind of insulation stuffed into the gap is a better solution. Filling the voids before sealing doesn’t take much additional effort, so it’s definitely worth taking the time to do it right.



Knee Walls Installed

Because our lot is sloped, the plans called for a series of knee walls:


The guys installing the knee walls (left to right: Johnny, Nils, Sammy, and Billy).

When I saw the first piece of Zip about to be installed, I realized the bottom edge, which is exposed OSB, would be sitting directly on top of the Roxul on the foundation. While it’s unlikely that water will find its way to this edge (the flashing for the wall assembly will be installed over the exterior face of the Zip at the bottom of the wall), it seemed like a good idea to tape this edge with the Tescon Vana for added protection and peace of mind (even if it only protects this exposed edge until the rest of the wall assembly is installed).


First piece of 7/16″ Zip wall sheathing installed.

Knee wall pictured below had all exposed seams in the framing lumber filled with the Contega HF sealant before also applying the Tescon Vana tape, all of which was done prior to the Zip sheathing being installed. The sealant takes about 48 hours to cure enough before you can effectively cover it with the Pro Clima tapes (something to consider when setting up scheduling goals).


Knee wall being covered in Zip sheathing.



Close up of knee wall with Zip sheathing and sealed seams.

For the bottom, exposed edge of the Zip sheathing, I cut the Tescon Vana tape like I was wrapping a present…

Once the Zip sheathing was installed on the knee walls, I could move into the basement and seal up the connections between the Zip and the framing members, in addition to hitting any seams in the framing itself.

Once the house gets closed in, I will go back and tape the connection between the top of the foundation and the mudsill for one last layer of protection against air infiltration.


Knee wall with Zip sheathing after sealing up all the connections.




We decided to use Huber’s Advantech Subflooring after years of reading about it in Fine Homebuilding magazine, and based on the online comments from installers who see the added benefits that come with what is an admittedly higher price point. For instance, it’s more resistant to moisture, so it should produce more stable, flatter flooring (e.g. hardwood or tile) when the house is complete, in addition to preventing annoying floor squeaks.

Billy Phil Nils first pieces of subflooring

First sheets of subflooring being installed by Billy, Phil, and Nils.

In order to maintain a high level of indoor air quality (IAQ), we’ve been seeking out low or no VOC products. So, in addition to the Advantech subflooring, which is formaldehyde-free, we chose the Liquid Nails brand of subfloor adhesive (LN-902/LNP-902) because it is Greenguard certified. Another great resource for anyone trying to build or maintain a “clean” structure is available at the International Living Future Institute website: The Red List


The product takes much longer to dry when it’s cold and wet outside — at least 2-3 days in our experience (sometimes even longer). It’s nice to see more “green” products showing up in the big box stores, rather than having to always special order them.



Standing by what will be the kitchen door. The subflooring was installed with nails and Liquid Nails subfloor adhesive.



Corner of our slowly growing wall assembly. The connection between the subflooring and the top of the rim joists was eventually sealed with the Contega HF sealant. 

Basement slowly being covered by subflooring:



Walls Go Up


Our blank canvas.

Our wall assembly is almost entirely based on Hammer and Hand’s Madrona House project, which I discuss here: Wall Assembly

In preparation for construction, I built a mock wall assembly in order to easily explain to anyone on site how the various components should go together. It also gave me a chance to practice using the Contega HF sealant, along with the various Pro Clima tapes from 475 High Performance Building Supply.

It’s been exciting to see the walls go up, incorporating the many details in the mock wall assembly.


Men at work: Zach, Phil, and Sammy laying out the walls.



Zach and Phil installing the Zip sheathing over the framing.



Phil laying down a consistent and continuous bead of construction adhesive (trying to avoid a bead that runs back and forth between fat and thin), before the Zip sheathing is installed.



We were fighting the rain, ice, and mud, but I was able to get the Tescon Vana tape over some of the seams in the Zip sheathing before the walls went up.



Sammy and Billy help me apply the Contega HF sealant to each nail hole, and then make it lie flat with a swipe of the spatula, so the Tescon Vana tape that will be applied later will also lie flat.



Section of wall nailed, taped, and nail holes caulked — ready to be raised up.

The final step before the walls were raised was to staple the B75 gasket to the bottom of each sill plate.


First section of wall going up: Billy, Zach, and Sammy doing the heavy lifting.



Zach establishes plumb, while Phil readies to make the wall secure.



The guys continue with the south walls.

View from north-east corner of house, and the guys framing in the shadow of the water tower:

The only section of wall where the B75 gasket rolled up on itself is shown below — no doubt because this was the most difficult section to get into place because of the stair opening. Otherwise, the guys had no issues with the gasket.

Even on this wall where the gasket did roll up on itself, I will cut off the excess that ended up on the interior side before sealing the connection with the subflooring, and then spend some time filling the void on the exterior side with backer rod and sealant as well.


Zach is the only dedicated, full-time framing carpenter on the crew (the other guys do a variety of carpentry-related work). He has a production background, and it shows with the energy and ease with which he works. He clearly enjoys what he does for a living (Zach, Sammy, and Billy). Sammy and Billy may not realize it yet, but they’re learning a lot from him (even if he does razz them all day long).

Below you can see some of the junctions where different materials meet, and the effort that’s going into air sealing these inevitable gaps: sealant at rim joist corners, rim joist – subfloor connection, and gasket under the wall sill plate:


Wall is up.



Same corner as above, but looking down exterior side of the wall.

We’ve tried very hard to keep foam out of the wall assembly and the overall structure itself (based on environmental concerns), however, one place where it did find its way in was the insulated headers for above our windows and doors:


Billy and Sammy putting the insulated headers together.



End of the day. The fourth wall awaits.



First look at what will become our front facade.

Once the perimeter walls were up, I went around with an impact driver and decking screws to tighten the connection between the Zip and the framing members, especially at the top of the walls. Although the Liquid Nails adhesive helps a lot, it still makes for an imperfect connection between the sheathing and the framing members:


Looking down at the top plate. The visible gap is between the side of the top plate and the Zip sheathing. I was able to close gaps like this one at the top of the walls using decking screws. The decking screws also closed similar gaps around window and door rough openings. This should make sealing these areas easier, and the connection more durable.



Leaning over the top of the wall to install the decking screws.

Having seen construction adhesive and nails in action, I would recommend a glue-and-screw approach if you’re trying to fully maximize the tightness of the connection between the sheathing and the framing.


Nice view as I apply the sealant.



My wife giving our Zip sheathing blue chicken pox with the Tescon Vana tape in order to seal all the nail holes.



It’s difficult to see, but this tape is embedded inside a sheet of ice. It rained overnight, before turning to ice. We’re asking a lot of these tapes and sealants. This piece of tape looks like fingertips holding on for dear life.



The Beast gets a first glimpse of the view from her bedroom window.



I was wondering why I would ever need more than one of these. Now I know — bent, scratched, and cracked, the Pressfix from 475 HPBS did its job well.

Foundation Details (Air Sealing #1)



For the top of the footings we used a product from Cosella Dörken called Delta Footing Barrier. Acting as a capillary break, the membrane is supposed to help prevent moisture from wicking up from below the footing, where it could then migrate into the foundation wall and into the basement, or even the wall assembly above (worst case scenario), causing mold or other moisture related damage. It should contribute to making the basement a very livable space (especially when combined with significant amounts of insulation on the exterior walls and under the slab).

Here’s a detail from the construction drawings:


Red arrow shows thermal bridge and gap in the vapor barrier up through the footing from surrounding soil if Delta membrane were not present.

In other words, this junction represents a weak point in our thermal envelope and vapor barrier. Passive House proponents often talk about using a red pen on a construction drawing to follow the air barrier and thermal envelope (the goal: no gaps in air sealing or the layers of insulation) . In theory, you should be able to do this all the way around the structure without once lifting your pen. If you can lift your pen (meaning there’s a gap in your air barrier or thermal envelope — which would be the case without the Delta membrane on top of our footing), then it’s a weak point that should be addressed (if at all possible).

Even with significant insulation on the exterior wall of the foundation (Roxul Comfortboard 80: 2″ + 3″), along with a sprayed-on waterproofing membrane, as well as a vapor barrier (Stego Wrap) and insulation (Roxul Comfortboard 80: 2″ + 2″) under the basement slab, this junction where the three elements meet — slab, footing, wall — is a weak point. Although it doesn’t address the weakness in R-value, at least it should keep the moisture at bay (probably the biggest complaint associated with basements).

With a 9′ basement, we’re hoping the temperatures at this depth are consistently mild enough to avoid any kind of significant energy penalty. I’m confident this will be the case because in our last home, a typical suburban tract house without much insulation, the basement always stayed cool in the summer and warm in the winter, even though the ducts to the basement had been closed off so the space never saw any direct benefit from the HVAC system.

For minimal cost in materials, the Delta membrane seems well worth it for the added peace of mind.


Rolls of Delta Footing Barrier on site and ready to go.


Here is a video and some photos from our job site:



The guys from Tynis Concrete didn’t seem to mind trying something new, and the membrane went on without any issues.



A corner of the footing with the Delta membrane “keyed” into the footing.


I couldn’t find any local suppliers who carried the Delta membrane, so I ordered online from:



Detail of the bottom of our hole, being prepped for the footings.



Foundation Walls with Roxul Comfortboard 80

For the walls, first we used a spray-on waterproofing membrane from Tremco:

After the waterproofing was complete, we began installing the two layers of Roxul Comfortboard 80 (a dense, rigid form of insulation that can be used below grade, to the exterior side of wall sheathing, and even under a basement slab), which will give the basement foundation walls an R-20 of insulation value.


Roxul delivery shows up on site (Comfortboard 80: 2″ and 3″ thick). Roxul is showing up in the Big Box stores here in the Chicago area, so it’s becoming easier to order.

When questions came up about how to install Roxul, or which product to use where, their technical help via email was great — in our case, Fiona Schofield, who gave us a lot of useful information — including the document below, a study on the long-term condition of Roxul (aka stone, rock, or mineral wool) in a below grade application (i.e. up against an exterior foundation wall):

external-thermal-and-moisture-insulation-of-outer-basement-wall (pdf)

In addition, after finding the video below online, in which what looks to be a European version of Roxul is attached to a cinder block wall with an adhesive, or a thinset mortar,

I contacted Fiona and heard back that it was ok to use an adhesive for our first layer (PL Premium, or similar polyurethane adhesive caulk), so long as we used a mechanical fastener for the second layer. In effect, the first layer just needs to stay on long enough for us to get the second layer up and attached with a mechanical fastener. This really saved us some time since the guys didn’t have to drill two full sets of holes.


Sammy hitting the back of the Roxul with Liquid Nails before setting it into position. The adhesive worked really well at keeping the Roxul in place, even when the foundation was damp in certain areas.

The guys also didn’t seem to mind cutting or otherwise working with the Roxul. We used serrated knives we purchased from Home Depot, made especially for cutting rock wool…


This knife, purchased from Home Depot, works really well cutting the Roxul.

… which worked fine, but then after some experimenting, the guys also began using a small, handheld sawzall (reciprocating saw), and even a table saw, to get the exact sized pieces we needed to ensure staggered seams. I had my doubts about the table saw, but Phil said the Roxul cut easily, and it really didn’t seem to kick up a lot of dust (although he did wear a dust mask for protection).


Billy and Nils (in the hole in the background) gluing up the first layer of Roxul.

Once the first layer of Roxul (2″ thick) was in place, we could then install our second layer of Roxul (3″ thick) over the top of it.

After a lot of research, and even posting a question on Green Building Advisor…

Attaching Roxul Comfortboard 80 to Exterior of Foundation Walls

… we decided to go with the Rodenhouse fastener (Plasti-Grip PMF):

These really are as easy to install as depicted in the video. Using a hammer drill with a 5/16″ bit, the guys drilled a hole to the depth of the fastener, before tapping the PMF fastener home with a hammer. It’s a genuinely straightforward process. Sometimes a fastener wouldn’t sit perfectly, but as long as a majority of the fasteners on each board did, it didn’t seem to be a problem. Based on what I read online, they were much easier to work with than if we had to use Tapcon or similar concrete screws.


Close up of the Rodenhouse PMF fastener.

They weren’t cheap, but they were well worth the cost in materials for the savings in labor (and frustration). And Mitch Mahler, from Rodenhouse, was easy to work with via email in terms of ordering or getting answers to technical questions.


The box the fasteners came in.



In the trenches, as the second layer of Roxul gets attached with the Rodenhouse fasteners.



Long, narrow piece of Roxul with 3 Rodenhouse fasteners.

Normally, Roxul recommends 5 fasteners per piece (4 in the corners, 1 in the middle), but we found that 4 on a normal piece, and 3 for a long, narrow piece worked fine — at least for the foundation, where the backfill will help to keep the Roxul in place over the long haul.



Thermal Bridging in the Foundation

Following Passive House science principles, we tried to remove as many points of thermal bridging in the structure as we could. One area where this was addressed in the construction drawings was a 7″ thermal break between the basement foundation and the attached garage foundation. In other words, there would be no physical connection between the garage and house foundations at all. The only connection would occur above, at the level of framing, where they would be tied structurally together. The idea was that we could place our two layers of Roxul (2″ + 3″) in that gap, thus maintaining our 5″ of Roxul on the exterior of the foundation, uninterrupted (the key point here) around the perimeter of the basement foundation.

On the day the footings were installed, however, our concrete subcontractor expressed serious reservations about the long-term structural stability of the framed house and garage above this gap — in effect, he was worried that over time the two foundations might settle and move apart, wreaking havoc with the framed structures above.

So I was back to post another question on Green Building Advisor (a fantastic resource for any green build or self-build) on the topic:

How important is a thermal break between a house foundation and an attached garage foundation?

Here are some photos showing these connections:


Garage foundation meeting up with corner of house foundation (north side of house).



Close up of this garage-house foundation connection, from inside the garage.



Front porch. Thermal bridge from garage to house is off to the far right.



Inside corner of garage where garage-front porch-house connect.



Outside corner of front porch. Technically, another thermal bridge from porch to house foundation.



Wing wall for side porch stoop. Yet another thermal bridge to the house foundation.

Unfortunately, there just doesn’t seem to be a lot of information available as to how to proceed. In the end, we decided to ignore these connections, hoping that the thermal bridging at these two points (garage-house, garage-front porch-house), in particular, won’t be all that significant (to our heating and AC costs, or, for example, cold getting into the foundation and then rising up and getting into the wall assembly above these two points where it could become interstitial condensation — unwanted, and potentially dangerous, moisture in the wall).

I assumed Passive House builders would incorporate rigid foam insulation into the concrete forms at these points, but I couldn’t find any pictures or descriptions showing or talking about this in books, magazines, or anywhere online. Either Passive House builders ignore these kind of connections, or I just missed the information somehow. 

*** If anyone knows of good sources on this, let me know, and I will post links here to help others in the design stage of their own build ***

Update: David Goodyear is building a Passive House in Newfoundland, and he has successfully used rigid foam between the house and garage foundations. You can read about it on his blog here:

Flat Rock Passive House: A Tale of Two Foundations

BEFORE: Monument to Italian Brutalism.



AFTER: Wrapped in snuggly blanket of Roxul. The wing wall was eventually entirely covered except for the tops.

Below are the other points of thermal bridging in the foundations, now covered in Roxul:


Corner of garage foundation meeting up with house foundation (standing inside garage).



Same corner, from outside, looking at house foundation to the right.



Garage-front porch-house connection (from inside garage).



Outside corner of front porch meeting up with house foundation.

We did our best to cover these thermal bridges, but clearly it’s imperfect, so all we can do is hope there won’t be a significant energy penalty associated with these connections.



Basement Windows and Roxul

As the Roxul was going on the foundation, Phil and Nils installed window bucks for the two basement windows. The bucks were sized so they meet up flush with the two layers of Roxul. Eventually a layer of HardieBacker board and two coats of Tuff II (the product we’ll be using for the parge coat) will cover the window bucks, and also the transition between the top of the foundation walls and grade around the perimeter of the house.


Nils installing the basement window bucks as the Roxul is being installed on the exterior side of the foundation.

I initially intended to use the R-Guard line of liquid membranes by Prosoco for air sealing and waterproofing all seams and window/door openings, but cold temperatures made this impossible (they require 40° F and rising, which would be the exception rather than the rule here in Chicago for December and January). Maybe because of years house painting (caulking and drywall patching) the liquid membranes seem easier to use and less fussy to get right (the big issue with the tapes is avoiding wrinkles and properly shingle flashing to get water moving in the right direction).

Our Plan B was the series of Pro Clima products sold by 475 High Performance Building Supply. Most of them, including the sealant, can be used down to 14° F without issues.

Another option would’ve been the line of Siga tapes, another popular choice used in Europe, available from Small Planet Supply.

So as the window bucks went in, I followed, applying Contega HF sealant to all the seams and gaps. The sealant is acting as our first layer of air blockage. It’s super sticky, so I don’t doubt that it’s permanently flexible. I did a mock-up of our wall assembly months ago, and the HF on the seams is still tacky to the touch. It goes on light green, then slightly darkens as it dries.


Contega HF sealant in a 20 oz. sausage. It’s also available in the more familiar 10 oz. caulk tubes.

A few suggestions for using the HF Sealant:

  • I’ve found that completely snipping off the metal clip on the end of the sausage (as opposed to just cutting a couple of small slits around it) prevents it from getting jammed in the front end of the gun.
  • If I have a half-finished sausage of HF at the end of the day, I put it in a tightly wrapped plastic bag overnight (see photo below), which allows me to use it within a day or two without any problems.
  • Use a tiny spatula (see photo below) to tool the HF into place rather than your finger, as you normally would with a caulk — it’s just too sticky.
  • Because the HF is so sticky, I wear Nitrile gloves, so when it starts to get everywhere — and it will get everywhere if you let it — I just simply change to a new pair.
  • For clean up, the Citrus Solvent we’ve been using with the tung oil works great.

The Newborn brand of sausage gun we’re using for the HF sealant. Found it on Amazon. A really well-made tool.



Found this on Amazon. I thought it was construction grade, but it’s made for kitchen use. It’s durable, and I like the thin blade since it offers more “feel” than a thicker blade, making it easier to tool the HF into place without displacing too much of it in the process.

It’s easy to forget the realities of a construction site when planning details, like the use of the Pro Clima tapes. I pictured it being a pretty straightforward process, not a winter day in the 20’s, fingers numb, propped up on an unbalanced ladder in the hole, while the other guys are cutting wood and Roxul around me — a case of adapt or die, I guess, and a reminder not to be too overconfident about the products you’ll be using, or the installation process that inevitably goes with them.


Applying the Pro Clima tapes to the exterior side of the window bucks.

It was important that the connection between the window bucks and the concrete of the foundation be air sealed and made water tight before it gets completely covered by the two layers of Roxul.

It’s been in the 20’s and 30’s, so the HF sealant took a couple of days to firm up before I could then apply the series of Pro Clima tapes. I’m using a combination of tapes, including the Tescon Vana (the bright blue), Profil (light blue — great for making inside and outside corners), Contega Solido Exo (black, 6″ wide), and the Extoseal Encors for our sills (475 HPBS has a great series of videos showing how to use each tape).


Finishing off the buck from inside the basement.

We knew the bucks would be sitting for some time, exposed to the elements, before the windows actually show up, so we decided to completely cover the openings just to be safe. This gave me extra practice using the tapes, which definitely helped, and it meant not stressing out every time the forecast called for rain or snow.


Basement window buck covered in Contega HF sealant and Pro Clima tapes.

The only tape that’s giving me fits is the black Contega Solido Exo. It’s thinner than the other tapes, so it has a propensity to want to stick to itself (wrinkles are more difficult to avoid), and I find it much harder to pull it away from its peel-and-stick backing than the other tapes. I worried that the Extoseal Encors might be difficult to get right, but it — along with the Tescon Vana and Profil tapes — has been surprisingly easy to work with.

This video was my Bible for installing the Extoseal Encors:

In lieu of on-site training from someone who’s used a specific product consistently, videos like this one are invaluable when using new products and you want to get the details right. Without videos like this, you’d be in for a frustrating process of trial and error.

For instance, even with this excellent video, I noticed when I did our mock wall assembly that because the Extoseal Encors can stretch around corners it’s easy to stretch it too much, thereby inadvertently thinning it out. I’ve found that when I get to a corner it’s better to just fold it around the edge rather quickly, without overthinking it too much, which helps to maintain the thickness of the material at and around the corners (arguably the product’s strongest attribute in helping to avoid water damage).

I can’t recommend enough doing a mock wall assembly, or practicing on scraps, to get a feel for using these products, before you find yourself on-site doing it for real.


Basement window buck sealed and taped on the exterior side before being covered in Roxul.



Basement window buck surrounded by two layers of Roxul.



Close up of outside edge of basement window buck and Roxul connection.

We’re almost ready to climb out of the hole. It will be exciting to watch the guys start framing so we can see the basic form of the house begin to take shape.


Tools ready to head to the next job site. Concrete guys (they’re mostly guys) are the unsung heroes of construction (excavators should be included as well) — like offensive linemen in football, no one pays much attention to them until a mistake is made.



Concrete jewelry.



Queen of Dirt Mountain.


Wall Assembly


Or: Dude, what’s in your walls?

When choosing what to put in our walls, we knew we wanted to try and balance high R-values (well above the current building code) with a limited environmental impact.

Here are three articles that address the issue:


(no foam)


After evaluating various materials, including sheep wool,

we decided to use many of the following elements employed by Hammer & Hand:


Hammer & Hand wall assembly for their Madrona House.

In terms of materials, there are any number of options for putting a wall assembly together. For instance, we really wanted to use the sheep wool, but cost and worries (unfounded or not) about availability, led us eventually to Roxul (the Hammer & Hand videos below proved especially helpful in this regard).

After seeing the wall assemblies Hammer & Hand has been using, and how they’ve evolved over time, we felt the Madrona House set-up represented a good balance between cost-environmental impact-availability-ease of installation. We will also be following their lead by using the Prosoco R-Guard series of products to help with air-sealing our building envelope.

Nevertheless, we did make a couple of changes to the Madrona House set-up. For example, we’re using 4″ of Roxul Comfortboard 80 on the exterior side of the Zip sheathing (based on our colder climate zone), and we will be using Roxul R23 batts in the stud bays, along with the Intello vapor retarder, stapled and taped to cover the stud bays. Otherwise, we will be sticking pretty close to the Hammer & Hand Madrona House wall assembly.

So from drywall to exterior siding (interior – exterior), this will be our wall assembly:

  • 5/8″ Drywall
  • Intello Plus vapor retarder (475 High Performance Building Supply)
  • Roxul R23 Batts in 2×6 stud bays (24″ o.c.) (
  • Zip board (for structural sheathing and WRB; seams covered w/ Joint and Seam Filler)
  • 4″ of Roxul Comfortboard 80 (two layers: 2″ + 2″)
  • 2-Layers of 1×4 furring strips (aka battens or strapping) as a nailing base for the cedar siding
  • 1×6 T&G Cedar (charred and oiled with a few boards left natural as an accent — most of it oriented vertically, hence the need for a second layer of furring strips).

A crude rendering of our wall assembly using my daughter’s colored pencils.

A collection of helpful videos explaining the various elements we’re going to use, and why they’re effective:

Without the information available from sources like Building Science Corporation (they have a lot of interesting research documents) and design-builders like Hammer & Hand (not to mention Green Building Advisor and similar sites and forums that allow consumers to Q&A with expert builders and designers in “green” architecture), trying to build structures to such exacting standards (e.g. Passive House – Pretty Good House – Net Zero) would be exceedingly difficult, if not impossible, for those without previous, direct experience in this type of building program. I can’t express how thankful I am that so many individuals and businesses like these are willing to share their years of experience and knowledge with newbies like myself.

Here are the Hammer & Hand videos that initially sparked my interest in using Roxul rather than foam:

Instead of using tape for exterior seams, we are going to use the R-Guard series of products from Prosoco:

For various interior seams and connections we anticipate using the Tescon Vana tape, or an appropriate gunned sealant.

Helpful Links

GBA (Green Building Advisor): Building Green (Starter Q&A)

GBA: Article on minimum thickness of exterior foam by climate zone

GBA Question: Foam vs. Roxul

GBA: 10 Rules of Roof Design

GBA: “Greenest”

GBA: Passive House Design (5-part video series) Requires membership after Part I, but well worth it.

BSC (Building Science Corporation): Perfect Wall (pdf)

BSC: Hygrothermal Analysis of Exterior Rockwool Insulation (pdf)

BSC: Moisture Management for High R-Value Walls (pdf)

BSC: Cladding Attachment Over Thick Exterior Insulating Sheathing (pdf)

GBA: Mineral Wool Over Exterior Sheathing

Passivhaus Trust (UK): how-to-build-a-passivhaus-rules-of-thumb (pdf)

GBA: The Pretty Good House

GBA: Passive House Certification: Looking Under the Hood