kimchi & kraut

Passive House + Zero Net Energy + Permaculture Yard

Category Archives: PHIUS

Siding Part 1: Continuous Insulation with a Rainscreen

10

Continuous Insulation vs. Double-Stud Wall

Although builders can make either approach to high-performance walls work, we decided continuous insulation (or CI for short) made the most sense to us. And while continuous insulation has its own challenges, especially in terms of air and water sealing details around windows and doors, intuitively we felt insulation on the outside of our sheathing would give us our best chance at long-term durability for the structure.

In spite of the fact that these kind of wall assemblies are climate specific, for anyone interested in the performance of various wall assembly approaches this BSC paper is an excellent place to start:

 

High R-Walls

 

Or you can check out Hammer and Hand’s evolving wall assembly strategies here:

 

Passive House Lessons

 

And here’s a mock-up wall assembly by Hammer and Hand showing many of the details we incorporated into our own house:

 

 

While many believe a double stud wall simplifies much of the framing, we decided that a continuous insulation approach, which in theory should better manage seasonal moisture changes inside the walls while it also eliminates thermal bridges, was worth the extra effort.

 

 

2 Layers of Rockwool over Zip Sheathing

Based on the drawings from our original builder, Evolutionary Home Builders, who was going to use 3.75″ inches of rigid foam, and the recommendations of both PHIUS and Green Building Advisor for our climate zone 5 location (leaning heavily towards PH performance), we decided to go with 4″ of Rockwool Comfortboard 80 on top of our Zip Sheathing.

For more information regarding how we came up with the specifics of our wall assembly, go here:

Wall Assembly

 

 

Finding Subcontractors for a Passive House

In the Chicagoland area it’s still a struggle to find builders or subcontractors who are knowledgable about, or even interested in, “green building”. In fact, despite our well-documented experience with Evolutionary Home Builders, clients continue to hire Brandon Weiss (Dvele and Sonnen) and Eric Barton (apparently now on his own as Biltmore Homes, or Biltmore ICF) presumably because the options here in Chicago remain so limited. We assume this is the case because we still get the occasional email from current or former clients who have also had a negative experience working with Brandon or Eric. In addition, even though PHIUS has dozens of certified builders and consultants listed for Illinois and the larger Midwest region, it’s unclear just how many of them have worked directly on an actual Passive House project.

Until there’s more demand from consumers, or the building codes change significantly, it’s difficult to imagine the situation improving much in the near future. This is unfortunate since particularly here in the Chicago area, or the Midwest more broadly, homes could really benefit from the Passive House model, or something close to it, e.g. The Pretty Good House concept, because of our weather extremes (dry, cold winters and hot, humid summers). The combination of meticulous air sealing, high R-values, and continuous ventilation associated with any high-performance build is hard to beat in terms of day-to-day occupant comfort, not to mention the significant reduction in both overall energy demand and the cost of utilities.

In our own case, when I think of all the individual trades we had to hire, securing a siding contractor was far and away the most difficult. Our HVAC contractor for the ductless mini-splits was already somewhat familiar with “green” building and PH, so working with me on air sealing details and dealing with a thick wall assembly didn’t worry him. Also, if I had it to do over, I don’t think I’d bring up all the PH details with a plumbing or electrical contractor when getting bids since the air sealing details are pretty straightforward and can easily be planned for and executed on-site after they begin their work (assuming someone else, most likely a rough carpenter, GC, or homeowner is tasked with all the air sealing chores). And if the concrete sub is unfamiliar with insulation under a basement slab, or over the exterior walls of the foundation, then it’s easy enough for framers, or even homeowners if necessary, to do this work, along with installing a vapor barrier like Stego Wrap before the basement slab gets poured.

For siding, however, because of the level of detail involved before the siding itself could be installed, it was a real challenge to even get quotes. As things turned out, we had nearly twenty contractors (a mix of dedicated siding contractors and carpenters) visit the job site before we received an actual estimate. Many of those who visited the job site expressed genuine interest, most going so far as to acknowledge that this kind of wall assembly made sense and would probably be mandated by the residential code at some point in the future, but almost without exception they would disappear after leaving the job site — no bid forthcoming, and no response to my follow-up phone calls or emails.

Clearly they were terrified, not without justification, to tackle something so new, viewing our project through a lens of risk rather than as an opportunity to learn something new. From their point of view, why not stick with the type of jobs they’ve successfully completed hundreds of times in the past? It also didn’t help that I was a first time homeowner/GC, rather than a GC with a long track record of previously built homes in the area.

In addition, not only is continuous insulation over sheathing a novel concept in the Chicago area, especially in residential builds, even utilizing a ventilated rainscreen gap behind siding is almost unheard of — typically Hardieplank lap siding is installed directly over Tyvek or similar housewrap (this can be observed directly on hundreds of job sites across the city and suburbs). And this isn’t entirely the fault of contractors. For instance, how many homeowners when presented with the idea of continuous insulation, or a rain screen gap, balk at the extra costs associated with these techniques without carefully considering the potential energy savings or increased durability for the structure?

While there are any number of certified LEED projects in our area, and even some Passive House projects (both residential and commercial) in Chicago and the surrounding suburbs, for the most part consumers are still largely unaware of Passive House or other “green” building standards like Living Building Challenge. Clearly “green” building, let alone Passive House, has its work cut out for it here in the Midwest if it ever hopes to have a meaningful impact on the construction industry.

 

 

Installing Rockwool over the Zip sheathing

Mike Conners, from Kenwood Passivhaus, was nice enough to recommend Siding and Window Group, which definitely got us out of a jam. Thankfully, Greg, the owner, was up for the challenge and was nice enough to let us work with two of his best guys, Wojtek and Mark.

Initially Wojtek and Mark dropped off some of their equipment at the site the day before they were to start work on the house. This gave me a chance to go through many of the details with them directly for the first time. Although a little apprehensive, they were also curious, asking a lot of questions as they tried to picture how all the elements of the assembly would come together. In addition to the construction drawings, the series of videos from Hammer and Hand regarding their Madrona Passive House project were incredibly helpful (this project in particular was a big Building Science inspiration for us).

 

 

 

 

Also, this video from Pro Trade Craft helped to answer some of the “How do you…?” questions that came up during the design and build phases:

 

 

As sophisticated and intricate as some architectural drawings may be, in my experience nothing beats a good job site demonstration video that shows how some newfangled product or process should be properly installed or executed.

On the first day, while Wojtek and Mark installed the Z-flashing between the Zip sheathing and the foundation, along with head flashings above the windows and doors, I started putting up the first pieces of Rockwool over the Zip sheathing.

 

installing head flashing above wdw

We found it easier to embed the metal flashings in a bead of Prosoco’s Fast Flash. Once in position, an additional bead of Fast Flash went over the face of the flashing, ensuring a water tight connection between the metal and the Zip sheathing.

 

For the first layer of Rockwool we installed the pieces horizontally between studs as much as we could, knowing that the second layer of Rockwool would be oriented vertically. This alternating pattern helps to ensure seams are overlapped between layers so there aren’t any areas where the seams line up, an outcome that could undermine the thermal performance of the 2 layers of Rockwool.

 

z flashing nw corner

Z-flashing carried down over the exposed face of the Rockwool on the outside of the foundation walls — once installed, the gravel is pushed back so it covers the area where the flashing terminates on the face of the Rockwool. The other 3 sides of the house had much less exposure in this foundation-gravel border connection.

 

We didn’t worry too much about the orange plastic cap nails missing studs since they were sized to mostly end up in the Zip sheathing. In the end only a couple of them made it completely through the Zip without hitting a stud.

 

1st pcs rockwool going up n side

Putting up the first pieces of Rockwool on the north side.

 

Every so often Wojtek would come around the corner and watch what I was doing before asking questions about specific elements in the wall assembly.

 

orange cap nails for 1st layer rockwool

Plastic cap nails we used to attach the first layer of Rockwool. I purchased these from a local roofing supply house.

 

By the time I had about a quarter of the north side covered, Wojtek and Mark were ready to take over from me.

 

1st layer rockwool n side

First layer of Rockwool mostly complete on the north side. Before installing the bottom row of Rockwool we used shims to create a slight gap between the Rockwool and the metal Z-flashing on the foundation insulation to allow any water that ever reached the green Zip sheathing a clear pathway out.

 

In a pattern that would repeat itself with each layer of the remaining wall assembly, Wojtek and Mark would carefully think through the details as they progressed slowly at first, asking questions as issues arose, before getting the feel for what they were doing and eventually picking up speed as they progressed around each side of the house.

 

20171002_081038

Outside corner showing the Z-flashing covering the face of the Rockwool on the foundation with the first layer of Rockwool covering the Zip sheathing above.

 

Working through the many details with Wojtek and Mark — the majority of which occur at junctions like windows and doors, the top and bottom of the walls, along with mainly outside corners — was both collaborative and deeply gratifying. They demonstrated not only curiosity and an ability to problem solve on the fly, they also clearly wanted to do things right, both for me as a customer and for the house as a completed structure (it felt like both aesthetically and in building science terms).

 

1st layer rockwool at wdw buck

First layer of Rockwool meeting up with a plywood window buck. We tried to keep connections like these as tight as possible, especially since the window buck itself already represents a slight thermal bridge.

 

They never hurried over specific problem areas, arrogantly suggesting they knew better, instead they patiently considered unanticipated consequences, potential long-term issues, and actively questioned my assumptions in a positive way that tried to make the overall quality of the installation better. This mixture of curiosity, intelligence, and craftsmanship was a real pleasure to observe and work with.

 

starting 2nd layer rockwool n side

Mark and Wojtek beginning the second layer of Rockwool on the north side.

 

If a GC built this level of rapport with each subcontractor, I can certainly understand their refusal to work with anyone outside of their core team — it just makes life so much easier, and it makes being on the job site a lot more fun.

 

2nd layer rockwool at utilities

Second layer of Rockwool installed around mechanicals. Note the sill cock, or hose bibb: although it runs into the house, we left it loose so that it could be adjusted until the siding was complete — only then was it permanently soldered into place.

 

 

weaving outside corner w: 2nd layer

Weaving the seams at the outside corners to avoid undermining the thermal performance of the Rockwool.

 

 

2nd layer rockwool fastener at wdw

Close-up of the fasteners we used to attach the second layer of Rockwool.

 

For the second layer of Rockwool, Wojtek and Mark tried to hit only studs with the black Trufast screws. In fact, screwing into the studs with these fasteners, in effect, became a guide for accurately hitting studs with the first layer of strapping.

 

plates for 2nd layer rockwool

 

These Trufast screws and plates worked well and were easy for Wojtek and Mark to install.

 

trufast screw bucket

 

 

inside bucket trufast screws

The Trufast screws and plates were purchased from a local roofing supply house.

 

 

w side 2 layers rockwool

West side of the house with 2 layers of Rockwool complete.

 

 

1st layer rockwool into s side garage

First layer of Rockwool filling the gap between the house and garage framing.

 

If our lot had been larger, we would’ve gone with a completely detached garage, but unfortunately it just wasn’t an option.

 

2nd layer rockwool closing gap at garage

Second layer of Rockwool closing the gap between house and garage completely, ensuring our thermal layer is unbroken around the perimeter of the house.

 

 

nw corner 2 layers rockwool

Northwest corner of the house with the 2 layers of Rockwool installed.

 

It was exciting to see the house finally wrapped in its 4″ of Rockwool insulation.

 

 

Installing Battens and Creating our Rainscreen

Initially we were going to use 2 layers of 1×4 furring strips (also referred to as strapping or battens); the first layer installed vertically, attaching directly over the 2×6 framing members through the 2 layers of Rockwool and the Zip sheathing, with the second layer installed horizontally, anticipating the charred cedar that would be oriented vertically on the house.

Pro Trade Craft has many really informative videos, including this one on using a rainscreen behind siding:

 

 

Nevertheless, as the second layer of Rockwool went up, Wojtek and Mark pointed out that putting the siding in the same plane as the Rockwool/metal flashing on the basement foundation would be needlessly tricky. In other words, maintaining about a 1/8″ horizontal gap between the bottom edge of the vertical siding and the metal flashing on the foundation around the house would be nearly impossible, and any variation might prove unsightly.

As a solution, we decided to use 2×4’s for the first layer of strapping. By adding to the overall thickness of the remaining wall assembly it meant the eventual siding — now pushed slightly out and farther away from the Z-flashing covering the face of the Rockwool on the foundation — could be lowered so that visually it slightly covered what would’ve been a gap between the top of the metal flashing on the foundation insulation and the bottom edge of the siding. Wojtek and Mark also found that the 2×4’s were easier to install than the 1×4 furring strips directly over the Rockwool so that it didn’t overly compress the insulation (an easy thing to do).

Unfortunately, increasing the overall wall thickness with 2×4’s meant having to use longer Fastenmaster Headlok screws (it would also cost us later when it came to the siding on the north side of the house — more on this later). Apart from this change, the additional overall wall thickness mostly just increased the air gap in our rainscreen, which arguably just increased potential air flow while also expanding the drainage plane behind the eventual siding.

 

 

In one of the Hammer and Hand videos Sam Hagerman mentions that at least 1.5″ of screw should be embedded into the framing (excluding the thickness of the sheathing) for this type of wall assembly, but when I asked a Fastenmaster engineer about this directly he recommended a full 2″ of their screws should be embedded into the framing members in order to avoid any significant deflection over time.

As a result, we ended up using 8.5″ Headlok screws. The screws work incredibly well, requiring no pre-drilling, and they’re fun to use with an impact driver (keep your battery charger nearby). Along with the plastic cap nails and Trufast screws, I think we ended up with less than a dozen fasteners that missed the mark for the entire house — a testament to Wojtek and Mark’s skill. I was able to seal around these errant fasteners from the inside with a dab of HF Sealant.

 

headlok missed framing

Sealing around a Headlok screw that missed a 2×6 framing member.

 

During the design stage, using these longer screws prompted concerns regarding deflection, but based on this GBA article, data provided by Fastenmaster, along with some fun on-site testing, the lattice network of strapping (whether all 1×4’s or our mix of 2×4’s and 1×4’s) proved to be incredibly strong, especially when the siding material is going to be relatively light tongue and groove cedar.

For the garage, since insulation wasn’t going to cover three of the walls (only the common wall with the house was treated as part of the house wall assembly), we used significantly shorter Headlok screws for the first layer of furring strips.

 

monkey on furring strips

The Beast testing out the structural integrity of our strapping on the garage. Note the Cor-A-Vent strip below the bottom horizontal furring stip, helping to establish a ventilated rainscreen.

 

 

garage only 2x4s

Common wall inside the garage. Only a single layer of strapping was necessary in preparation for drywall.

 

Mark took the time to recess these screws to make sure they didn’t interfere with the eventual drywall.

 

recess 4 screws

Recessed Headlok screw on a 2×4 in the garage. Ready for drywall.

 

A small detail, but one of many examples showing Wojtek and Mark’s attention to detail, not to mention their ability to properly assess a situation and act appropriately without having to be told what to do.

Once the 2×4’s were all installed vertically through the structural 2×6’s as our first layer of strapping, Wojtek and Mark could install the components of the rainscreen, including the Cor-A-Vent strips at the top and bottom of the walls, as well as above and below windows and doors. In combination with the 2×4’s and the 1×4’s, this system creates a drainage plane for any water that makes its way behind the siding, while also providing a space for significant air flow, speeding up the drying time for the siding when it does get wet.

 

rainscreen2.jpg

Why use a rainscreen? Illustration courtesy of Hammer and Hand.

 

In addition to the Cor-A-Vent strips, we also added window screening at the bottom of the walls just as added insurance against insects. We noticed that on the garage, even without any insulation, the Cor-A-Vent didn’t sit perfectly flat in some areas on the Zip sheathing. Since the Rockwool on the foundation, now covered by the metal flashing, was unlikely to be perfectly level, or otherwise true, along any stretch of wall, it made sense to us to double up our protection in this way against insects getting into the bottom of our walls at this juncture.

 

starting 1x4s n side

1×4’s being installed horizontally on the north side in preparation for the charred cedar that will be installed vertically. Also note the Cor-A-Vent strips just above the foundation and below the window.

 

 

cor-a-vent-product-label

The main product we used to establish our ventilated rainscreen.

 

 

insect screen for rscreen

Window screen we cut to size for added insurance at the bottom of the walls around the Cor-A-Vent strips.

 

Wojtek and Mark also did a nice job of taking their time to shim the 1×4 layer of furring strips, thus ensuring a flat installation of the charred cedar.

 

shims behind 1x4s

Shims behind some of the 1×4 furring strips to ensure a flat plane for the vertical cedar siding.

 

This really paid off, not only making their lives easier when installing the tongue and groove cedar, but also providing aesthetic benefits in the overall look of the siding. This was especially true on the north side of the house, which has the largest area of charred siding with almost no interruptions, apart from a single window. It’s also the tallest part of the house, so without proper shimming the outcome could’ve been really ugly. Instead, once the cedar siding was installed it was impossible to tell there was 4″ of Rockwool and 2 layers of strapping between it and the Zip sheathing.

Really impressive work by Wojtek and Mark.

 

lking down furring behind rscreen at fdn

Looking down behind the ventilated rainscreen — 2×4, 1×4, with Cor-A-Vent and window screen at the bottom, just above the top of the foundation. This gap behind the siding provides ample air flow for the cedar siding, ensuring that the wood never remains wet for long.

 

 

rscreen furring at foundation

Strapping and rainscreen elements around a penetration near the top of the foundation.

 

Things got somewhat complicated around windows and doors, but once we worked through all the details for one window it made the remaining windows and doors relatively straightforward to complete.

Below you can see all the elements coming together: the window itself, the window buck covered with tapes for air and water sealing, the over-insulation for the window frame, the Cor-A-Vent strip to establish air flow below the window and behind the eventual cedar siding, along with the strapping that both establishes the air gap for the rainscreen while also providing a nailing surface for the siding.

Once most of the siding was complete around each window, but before the 1×6 charred cedar pieces used to return the siding to the window frames were installed, each window received a dedicated metal sill pan. The pan slid underneath the bottom edge of the aluminum clad window frame and then extended out just past the edge of the finished siding (I’ll include photos showing this detail in the next blog post about installing the charred cedar siding).

Here’s a JLC article discussing a couple of options for trim details in a thicker wall assembly with similar “innie” or “in-between” windows:

 

Window Trim

 

And here’s a detailed slide presentation by Bronwyn Barry regarding details like these for a Passive House wall assembly:

 

Sills and Thresholds – Installation Details

 

wdw rscreen and frame detail

The many details coming together around a window. In addition, each window eventually received a dedicated metal sill pan as a durable way to ward off water intrusion.

 

 

from int wdw rscreen and sill

Looking through an open window to the sill and the rainscreen gap at the outside edge. Note the Extoseal Encors protecting the sill of our window buck.

 

 

lking down wdw rainscreen

Outside edge of the window sill, looking down into the mesh of the Cor-A-Vent strip with daylight still visible from below.

 

 

rscreen at hd flash on wdw

Head flashing at the top of a window with doubled up Cor-A-Vent strips above it.

 

 

out corner hd flshng ready for sd

Same area, but with a 1×4 nailed across the Cor-A-Vent, creating a nailing surface for the cedar siding.

 

Many of the same details were repeated at the top and bottom of our two doorways. Below is a close up of the kitchen door threshold with Extoseal Encors and Cor-A-Vent again, along with additional metal flashing. Once a dedicated metal sill pan was installed (after most of the siding was installed), it felt like we did everything we could to keep water out.

 

kitch dr prepped 4 sd

Many of the same air and water sealing elements and rainscreen details present around the windows ended up at the top and bottom of doors as well.

 

In the photo below, you can see the many elements we utilized to try and prevent moisture damage around the front porch. For the door buck itself, I applied Prosoco’s Joint and Seam, both at joints in the plywood and the plywood/Zip sheathing connection, but also between the concrete and the door buck, as well as between the Rockwool and the concrete. We also kept the 2×4’s off the concrete, while also using the Cor-A-Vent strips to establish a ventilated rainscreen so that any moisture that does get behind the siding has ample opportunity to dry out in this area before it can cause any rot.

 

frt porch prep - rscreen water

Front porch: elements in place to try and prevent moisture damage.

 

 

west w: 2 layers battens

West facade prepped for siding.

 

 

flashing details on porch

Wojtek and Mark did a nice job with all the metal flashing details around the house — these kind of areas are the unsung heroes of a structure that manages water safely, and unfortunately go largely unnoticed by most homeowners.

 

In the next blog post I’ll go through the details for the top of the ventilated rainscreen when discussing how the charred cedar siding was installed.

 

Mark and Wojteck at front door

Mark and Wojtek installing Cor-A-Vent above the front door.

 

Even without the siding installed yet, it was especially rewarding to see all the underlying prep work involved in finishing our thermal layer and rainscreen come together so nicely.

 

Mark and Wojtek on the roof

Mark and Wojtek on the garage roof finishing up the battens for the front of the house.

 

Many thanks to Wojtek and Mark for executing all these details with such skill!

Blower Door (Air Sealing #9 )

2

When it was time to schedule our blower door test we considered using Eco Achievers, but we only knew about them because they’ve worked extensively on projects for our original builder, Evolutionary Home Builders. We decided the potential awkwardness, or even a possible conflict of interest, wasn’t worth pursuing their services. An example of guilt-by-association I suppose, one that is probably unfounded but, nevertheless, the strong affiliation with our original builder made it difficult for us to reach out to them for help. They also hired one of Brandon’s former employees (this employee was nothing but nice and professional towards us as we were deciding to part ways with Brandon), which would’ve only added another layer of awkwardness to the situation.

Unsure how to proceed, I looked online and found Anthony from Building Energy Experts. He was able to come out and do a blower door test for us, helping me hunt down a couple of small leaks, so that we ended up at 0.34 ACH@50 for this initial test.

Here’s a Hammer and Hand video discussing the use of a blower door:

 

 

On a side note: all of the Hammer and Hand videos, along with their Best Practices Manual, were incredibly helpful as we tried to figure out all the Passive House details related to our build. It’s no exaggeration to say that without Hammer and Hand, the Green Building Advisor website, BSC, and 475 HPBS, our build would’ve been impossible to accomplish on our own. I owe an incredible debt of gratitude to all of these great resources who invest valuable time sharing such a wealth of information.

Below is a Hammer and Hand video noting the importance of properly detailing corners to avoid air leaks:

 

 

Because of this video, I sealed all of my corners for the windows and doors like this:

 

HF Sealant in corners b4 blower door

Adding Pro Clima HF Sealant after completing taping of the corner, just for added insurance against potential air leakage.

 

I also added some HF Sealant to the lower portion of the windows, since some air leakage showed up in this area with Anthony where components of the window itself come together in a seam.

 

sealant on wdw components junction

Seam near bottom of window where components meet — sealed with HF Sealant.

 

Where components come together is often an area that needs special or further attention.

 

close up corner and wdw components seam w: sealant

Close-up of this same area — seam in components sealed, along with the bottom corner of the window and the gap between window buck and window.

 

Even with layers of redundancy in place, in the picture below there was a small air leak still present at the bottom plate – sub flooring connection. A coating of HF Sealant easily blocked it.

Once the stud bays were insulated (after most of the siding was up), the interior walls would eventually be covered with Intello (I’ll cover the details in a future post on interior insulation), adding yet another layer of redundancy for mitigating potential air intrusion.

 

area of kitchen sill plate leakage

Area of kitchen sill plate leakage.

 

Anthony didn’t have any previous experience with a Passive House build, so it occurred to me that it might be beneficial to reach out to Floris from 475 High Performance Building Supply (he had already done our WUFI analysis for us), and Mike Conners from Kenwood Property Development to see if there was someone locally who did. Mike is a Passive House builder in Chicago who had already helped me out with some Rockwool insulation when we came up short earlier in our project (the two GC’s we fired repeatedly struggled with basic math), and he was very nice to take the time to answer some other technical questions for me as well.

 

 

Both, as it turned out, ended up recommending that I contact Steve Marchese from the Association for Energy Affordability.

 

 

Steve would eventually make three trips to the house, doing an initial blower door test after the structure was weather-tight and all the necessary penetrations had been made through our air barrier, a second test after exterior continuous insulation was installed, and a final test after drywall was up to ensure there hadn’t been any increase in air leakage during the final stages of construction.

 

Steve starting blower door test

Steve setting up the blower door for his first test.

 

Following Passive House principles for our build, we also followed the same protocols for the blower door tests: Blower Door Protocol

With the structure under pressure from the blower door fan, Steve and I walked around the house while he used a small smoke machine in order to try and find any leaks that I could then seal up.

 

Steve testing window gasket

Steve starting at the windows. Here testing a window gasket for air leakage.

 

The gaskets around our windows and doors proved to be some of the weakest areas in the house although, comparatively speaking, it was inconsequential since the overall air tightness of the structure was fairly robust (favorite word of architects).

 

Steve showing impact of unlocked window

Steve showing me the impact a window in the unlocked position can have on air tightness. The gasket, ordinarily squeezed in the locked position, works to bring the sash and the frame tightly together.

 

 

Steve smoke at family rm wdw

Looking for areas around the windows that might need adjusting or additional air sealing.

 

For instance, even though no substantial air leakage showed up around this kitchen door, during our first winter this same door eventually had ice form outside at the upper corner by the hinges, on the exposed surface of the gasket where the door meets the frame.

 

Steve at kitchen door

 

After figuring out how to adjust the door hinges, there was no longer any ice showing up this winter, not even during our Polar Vortex event in late January.

 

 

Much the same thing occurred around our front door as well, with the same solution — adjusting the hinges to get a tighter fit at the gasket between the door and the frame.

 

Steve testing attic hatch

Steve testing the attic hatch for air leaks.

 

Steve was nice enough to go around and methodically check all the penetrations in the structure.

 

Steve testing plumbing vent in kitchen

Steve testing for air leaks around the kitchen plumbing vent and some conduit.

 

 

Steve testing for air leaks @ radon stack

Steve testing for air leaks around the radon stack.

 

 

Steve @ radon stack close up

Close up of radon stack during smoke test.

 

There was one area in the guest bathroom where the Intello ended up getting slightly wrinkled in a corner during installation. With Tescon Vana and some HF Sealant I was able to address it so nothing, thankfully, showed up during the smoke test.

 

Steve testing wrinkled area of Intello

Steve testing area of Intello that I inadvertently wrinkled during its installation.

 

After looking around on the main floor, Steve moved down into the basement.

 

Steve testing for air leaks @ main panel

Checking for leaks at the main electrical panel.

 

 

Steve testing for air leaks @ main panel exit point

Checking for leaks at the conduit as it exits the structure.

 

 

Steve testing for air leak @ sump pit cap

Looking for air leakage around the sump pit lid.

 

The lids for the sump pit and the ejector pit were eventually sealed with duct seal putty and some Prosoco Air Dam.

 

Steve testing for air leaks @ ejector pit

Testing the ejector pit for air movement.

 

 

Steve testing for air leaks @ Zehnder exit point

Checking for air leakage around one of the Zehnder ComfoPipes as it exits the structure.

 

 

Steve testing for air leaks @ pvc:refrigerant lines

Looking for air leaks around the heat pump refrigerant lines as they exit the structure.

 

 

Steve smoke at sump discharge

Checking around the penetration for our sump pump discharge to the outside.

 

Before the second blower door test, I was able to add some duct seal putty to the lids of the sump and ejector pits.

 

ejector pump lid w: duct seal

Ejector pit lid with some duct seal putty.

 

Below is a copy of Steve’s blower door test results, showing the information you can expect to receive with such a report:

 

Final Blower Door Test Results

 

For the last two tests Steve used a smaller duct blaster fan in order to try and get a more precise reading for air leakage.

 

Steve at front door

With Steve just after the initial blower door test was complete.

 

Steve would be back two more times — once before drywall, and once after drywall — just to ensure we had no loss of air tightness develop in the interim stages of the build (especially after continuous exterior insulation with furring strips were installed).

Here are the final figures noting where we ended up:

 

0.20 ACH@50 and 106 cfm@50

 

We are well below Passive House requirements (both PHI and PHIUS), so there was a great sense of relief knowing that all the time and effort put into air sealing had paid off, giving us the tight shell we were looking for. Even so, it was still pretty exciting news, especially for a first build.

And here’s an interesting article by 475 HPBS regarding the debate over how air tightness is calculated for PHI vs. PHIUS projects, and the potential ramifications:

 

Not Airtight

 

The Passive House Nightmare: Part 3

0

This can’t be happening again…

It is February of 2017 as I write this.

This project began for us back in the summer of 2014 — nearly three years ago — when we first sat down with Brandon Weiss in what was then his new office in Geneva, Illinois. As detailed here:

 

The Passive House Nightmare

 

Things didn’t go well for us with Brandon and his company, Evolutionary Home Builders.

After we decided to move forward and try to complete what we started, the question became:

Who do we hire as our next builder?

After our interactions with Mark Miller and Katrin Klingenberg, detailed here:

 

The Passive House Nightmare: Part 2

 

PHIUS (Passive House Institute US) did not seem like a resource we could utilize — the Passive House world is small, smaller still when you reduce it to a single geographical area like Chicago and its surrounding suburbs. And the thought of interviewing conventional builders, and trying to convince one to take on the detail required in a Passive House level build, seemed overwhelming.

As a result, we decided to go with two guys close to home who have conventional building experience.

The logic underlying the relationship was that they would GC the build, taking care of all the conventional building details, while I took care of all the Passive House details.

Unfortunately, this proved fruitless.

 

flooded basement

 

Events revealed they didn’t have the requisite skill set necessary to complete the job, and we have subsequently taken over the project ourselves. It’s taken weeks to get things back on track, hence the delay in posting anything new regarding the progress of the build.

 

job-site-shut-down-west-side

 

When the build is complete, I’ll return to this matter, offering more details that will hopefully help other consumers who want to build a new house avoid our unfortunate experience.

 

new beginnings

New beginnings.

 

The really sad thing is there are quality people who make a living as general contractors, but unfortunately it remains a minefield out there for consumers without meaningful connections. If you don’t already know the answer to the question ‘Who should build our new house?’ before you start the process, then it’s truly a case of caveat emptor. And if things should go poorly, you will feel like you’re on a very lonely island.

 

relentless

Relentless.

 

Details to follow…

The Passive House Nightmare: Part 2

0

Our original builder decides to settle, then disappears…

Back in early March, 2016, Brandon Weiss (owner of Evolutionary Home Builders) contacted me via voicemail and email letting us know he was interested in settling our dispute with him. This occurred — we believe not coincidentally — after he learned I had been in contact with his former clients, the Illinois Attorney General’s Consumer Fraud Bureau, and Katrin Klingenberg (founder and Executive Director of Passive House Institute US), in addition to leaving a review of EHB on the Houzz website.

He claimed he was willing to meet all of our terms — the same terms, in fact, that we had offered months ago — a partial refund of $15,000 (of the $30,000 we initially gave him), release of the copyright on our drawings, and releasing us from the contractual demand that we not build with any other contractor on our own lot for two years.

It became clear, after some back and forth, that Brandon was willing to settle, but only if we were prepared to sign a non-disclosure agreement, and only if we met with him in person. He was insistent on this last point. Brandon claimed it was because I had made public our exchanged emails and other documents pertaining to our case. We believe, however, that his intentions were to get us in a room in the hopes of intimidating us into accepting altered terms, or pressuring us to immediately sign an agreement without the benefit of review by our legal counsel.

After our lawyer asked Brandon to provide verbiage, meaning ‘what exactly do you expect us to sign’, prior to our meeting, Brandon disappeared — ceasing to respond at all — which, once again, only confirmed our suspicions regarding his real intentions all along.

Why disappear after we requested something as straightforward as seeing the document prior to our meeting? What’s in the language that’s so objectionable that we can’t see it beforehand? Who would be willing to sign a non-disclosure agreement without having their lawyer look it over first? Why do we have to sign it immediately, without ample time to review it? If normal real estate transactions can occur with only a client’s lawyer present, why not in this case? We feel Brandon has been less than transparent or fair with us, so why would we want to sit down with him ever again?

 

Alice wikia.com

Illustration by Sir John Tenniel.

 

Our original lawyer gave up on this as a lost cause, so we hired a second lawyer to contact Brandon one more time. Brandon’s response: ‘same terms — and, no, you can’t see the document beforehand’.

Why not meet our terms, which are pretty basic and more than fair, and move on? Why, instead, does he continue to take such a hyper-aggressive stance? Why be so ruthless?

Furthermore, if Brandon is so sure he’s done nothing wrong, why is he so afraid of the paper trail documenting our experience with him and his company? Why the lack of transparency and obsession with secrecy, and insistence on the need for a non-disclosure agreement if Brandon, Patrick, and Eric have nothing to hide?

Even in terms of construction related information, they act as if they’re doing something that has real proprietary significance (hence, the claim of intellectual property regarding the budget numbers), but they’re not. Virtually everything they do — the products chosen, the process of putting them together — is open-sourced on the internet, in books and magazines, and even in free videos on YouTube.

It’s always been my understanding that the Passive House community (and the larger Green Building Movement generally) prides itself on exactly this kind of openness since it’s supposed to benefit builder and client alike (e.g. Green Building Advisor, Proud Green Home, Building GreenMatt Risinger, GO Logic, Fine Homebuilding, along with countless other sites and forums).

 

… if Brandon’s original build budget numbers were accurate, then the premium to build to the Passive House standard is at least 25-30%, in which case PHIUS needs to stop telling consumers it is only 10%. If Brandon’s numbers, on the other hand, were less than entirely honest, why defend him?

 

In addition, if you compare Brandon and EHB’s attitude towards construction related information with another Passive House builder, Hammer and Hand, it’s hard to imagine how the contrast could be any more stark (think North Korea vs. South Korea). In Brandon’s case, he seems to treat virtually everything as intellectual property, while Hammer and Hand is busy giving away information through countless job site videos and their Best Practices Manual. Based on this alone, who would you trust to build your new house? Who would you entrust with your life savings?

It’s not as if Evolutionary Home Builders are Coca-Cola or KFC — there’s no secret recipe or formula for what they do. Even more to the point: What information in their possession is not readily available from any number of other sources? The IP claim is so weak that even if they broke down the construction budget by components and every phase of the build, with a dollar amount assigned to each one, it would still be a case of ‘so what’. No one, even at that point, would know how much of each dollar amount is profit or overhead, so the information is virtually meaningless.

Knowledge is nice to have, to be sure, but it means nothing without proper execution — as any venture capitalist in Silicon Valley will calmly explain before refusing to sign a start-up’s NDA. In other words, if you’re a Passive House builder, for example, put your time and effort into building high quality structures at a fair price that your clients are thrilled with (so your clients will sing your praises), rather than wasting time worrying about protecting information that’s so easily accessible anyway (via the internet, books, magazines, etc.).

Put still another way: If the sum total of what you believe is your intellectual property can be revealed and then successfully copied by others when simply written down on a piece of paper (e.g. budget numbers), then there probably isn’t much to protect to begin with. Isn’t this the implicit message sent by any number of builders, including Hammer and Hand, when they are so open about the details of how they build?

Consequently, it doesn’t seem to matter from which angle you approach the claim of intellectual property — product, process, or even how they price out a build — the claim itself rings hollow. All of which leads to the obvious question: If it’s not intellectual property that they’re trying to protect with a non-disclosure agreement, what is it that they want hidden from view?

 

Humpty_Dumpty wikia.com

Words by Lewis Carroll. Illustration by Sir John Tenniel.

 

The response to our situation by Passive House Institute US (PHIUS) also proved to be a disappointment. We have reached out twice now — originally to Mark Miller, and, most recently, to Katrin Klingenberg — yet, in each instance, our request for help was soundly rebuffed.

For example, after our budget meeting with Brandon and his team in late November, 2015, we contacted Chicago architect Mark Miller in early December, having found his information on the PHIUS website as a Certified Passive House Consultant and a Certified PHIUS Builder. Here is how that exchange went: emails.

What gets interesting is comparing the dates of our initial email exchange with Mr. Miller with Brandon’s email containing the bizarre offer (12-9-15 email) to send us to Belize. It doesn’t take a master detective to deduce what happened during that twenty four hour period between the 9th and 10th of December:

After Mr. Miller contacted Brandon or Patrick on the 9th to find out about our project, and one or both of them portrayed us in a negative light, that very same day Brandon sent us the Belize invitation — no doubt his lame attempt at soothing what he perceived to be our ruffled feathers. It was obvious what had transpired, so it wasn’t all that surprising to get Mr. Miller’s final, patronizing reply the next day on the 10th.

As to Mr. Miller’s points, specifically:

  • “… may not have been for a well-defined project…”  Our project has remained the same going back even before our initial meeting with Brandon: approximately 1600 sq. ft. single-story home, insulated well above code, with high-performance windows and doors, 2-BR, 2-Bath, main kitchen/family room area, a 9′ unfinished full-basement, charred cedar for the exterior siding, and we’ve kept the same flooring selections we originally started with, along with a basic door casing and baseboard trim package.
  • “… reduce costs to better help meet your budget.”  Only after EHB went way over budget. Only after we made it clear we were walking away. No doubt they would have been happy to see us just accept the $500,000 price and move forward with the build.
  • “… wish list items…”  What wish list items? The only thing we added after the preliminary budget was 66 sq. ft. of construction space (original 40′ x 40′ structure changed to 49′ x 34′ structure). We’re going for a pared-down design aesthetic based on our tastes, but also to save money, so there is no crown molding, chair railing, wainscoting, coffered ceilings, an oak-lined office, or master bathroom wrapped in Carrara marble. Clearly this is why the only “solutions” Brandon and his team came up with for cost savings during the November, 2015 budget meeting included dramatic structural changes, not altering or deleting extravagant interior design choices.
  • “… PH plaque…”  Mr. Miller refers to this twice, so I can only assume Brandon or Patrick put this in his head. To hint that our attitude was “Passive House certification or bust” is particularly grating since we asked if pulling back from the standard could produce meaningful savings in our May, 2015 meeting with Brandon and Patrick, to which they responded, “No, this is the way we build.”
  • “… wish list items…compromise somewhere… shift perspective… PH plaque… brag to your friends/family…”  It’s pretty obvious that Brandon or Patrick painted us as wildly unreasonable clients who wanted the world for a steal. I would argue the emails between Brandon and myself draw a very different picture.

 

wikia.com

“Curiouser and curiouser!” Lewis Carroll. Illustration by Sir John Tenniel.

 

In Mr. Miller’s defense, we were not his clients, and he was basing his response to us on what Brandon or Patrick told him. Nevertheless, we were asking for help, and we did offer to show him everything related to our project, but unfortunately he ignored the offer.

When we reached out to Ms. Klingenberg, we fared no better: emails.

We were not expecting her to act as judge or jury, we were genuinely asking for help in the form of guidance:

  • Why were the numbers of the build budget so different from those outlined in the PSA?
  • What did Brandon mean by “additional Passive House components were necessary” (because he never told us, even though we repeatedly asked)?
  • What could we have done differently?
  • Since the Passive House community is so small, who could we trust, moving forward, to not have a conflict of interest with Brandon? Is there an architect, a general contractor, or Passive House consultant in the Chicago area that they thought we could reach out to?

Instead we got the more polite equivalent of: ‘Shut up. Go away.’

Why is their first impulse to try and put me in my place, to try and squash me? It must be said, the arrogance on display throughout this process has been startling. Is it really so difficult to be nice to other people — especially when they are asking for help?

 

wikia.com Queen of Hearts

The Queen of Hearts. Illustration by Sir John Tenniel.

 

Regarding Ms. Klingenberg’s response, in particular, what is[Brandon’s] side of the story”. She doesn’t choose to share it with us. And what exactly justifies any builder taking $30,000 from a client and then giving them nothing in return?

As to her suggestion, “the next steps are outlined in your contract,” does she really believe, quoting the PSA now, that “[forced] arbitration before the Northern Illinois Home Builders Association” is the best setting for us to get a fair hearing? This is like suggesting that if a customer had a dispute with ExxonMobil it would make sense to ask the American Petroleum Institute to act as referee.

And I’m certainly not alone in believing forced arbitration to be an overly business-friendly, Kafkaesque joke ( Bill  /  Study Shines Light  /  Part I   /  Part II  ), with serious consequences for consumers, and even for the overall health of democracy in America (#ripoffclause). In fact, there is a growing movement in the US pushing members of Congress to prohibit forced arbitration clauses altogether. When people with authority (the arbitrator) have the option to take the side of the strong against the weak, regardless of the evidence (after all, it’s the companies who pay for the arbitrator), justice is rarely going to be the result.

 

 

It’s also surprising, even reprehensible in my opinion, that PHIUS not only tolerates but apparently supports forced arbitration. As an institution they portray themselves as enlightened and forward-thinking, so how can they allow their certified members to utilize such deeply flawed, even reactionary, language in their contracts with clients?

 

Where do Ms. Klingenberg’s loyalties lie: with the certified members, or with the homeowners? If the honest answer is with the certified members, then this is useful information for any consumer weighing the costs associated with a certified Passive House build.

 

If the construction industry is serious about cleaning up its reputation (and make no mistake about it, its current status is horrific — e.g. when we tell anyone that we’re building a new house the typical response is roughly: ‘why would you want to put yourself through that?‘), then getting rid of forced arbitration clauses in contracts would be an excellent place to start.

Which prompts several questions:

  • Why isn’t PHIUS out front leading on this issue?
  • If not PHIUS, then who? It’s a certainty that The National Association of Home Builders won’t be leading the charge.
  • Why doesn’t PHIUS require their certified members to eliminate all forced arbitration clauses from their contracts? 

If their answer is: ‘it’s current industry standard’ — well, so is building to code, but they don’t tolerate that. PHIUS holds their members to a higher standard when it comes to the structure, so why give them a pass on how they treat the human beings who have to pay for them and live in them?

Maybe more to the point: Why are they using forced arbitration as an excuse to ignore Brandon’s behavior?

 

“…as a 2009 Economist editorial put it, ‘You cannot claim that your mission is to ‘educate the leaders who make a difference to the world’ and then wash your hands of your alumni when the difference they make is malign’.”
 —Martin Parker, “Why We Should Bulldoze the Business School”

 

Isn’t a PSA document like the one used by Brandon and EHB a license to defraud clients? By including language such as a non-refundable deposit, and insisting on forced arbitration before an industry paid-for arbitrator, a client has no meaningful options should a dispute arise.

And if, in fact, Brandon baits potential clients with a reasonable sounding preliminary budget in the PSA (this is what we believe he did to us), taking a hefty down payment at signing, and then switches that budget number significantly, and without cause, when presenting a build budget (again, what we believe he did to us), by definition the client has no effective means of defending themselves. It’s a case of Hobson’s choice –— take what’s offered (a ridiculously exorbitant budget) or get nothing at all (again, what we believe happened to us).

Moreover, when Ms. Klingenberg suggests, “We can try to help with advice during the certification process…”, it sounds like she’s more than happy to take our money for certification, but she otherwise can’t be bothered to address what Brandon and EHB have done to our life savings, the time we have lost, or the needless stress that has been inflicted — even when, in large measure, it was their PHIUS stamp of approval (via certification) that encouraged us to pursue a build with Brandon and EHB in the first place.

 

wikia.com Sir John Tenniel

Tweedledum and Tweedledee. Illustration by Sir John Tenniel.

 

Mr. Miller’s and Ms. Klingenberg’s replies exhibit a total indifference to the facts at hand. Apparently they would prefer to close ranks around Brandon and EHB rather than confront what Brandon has done to me and my family — taking $30,000 of our life savings and giving us, quite literally, nothing in return. If their responses are any barometer, then clearly PHIUS believes this to be a fair exchange.

Also troubling, if the Passive House concept is ever truly going to be a mainstream idea, rather than perceived as a niche design option for the wealthy, doesn’t PHIUS and its certified members want people like my wife and I — a high school teacher and a stay at home parent — to pursue and even celebrate the Passive House standard? After all, they have a tab at the top of their website soliciting donations for the cause: “Help Make Passive Building Mainstream”.

Moreover, if the premium to build to the Passive House standard is really only 10%, then, considering our own experience, what other conclusion is there but that the fix is in? In other words, if Brandon’s original build budget numbers were accurate, then the premium to build to the Passive House standard is at least 25-30%, in which case PHIUS needs to stop telling consumers it is only 10%. If Brandon’s numbers, on the other hand, were less than entirely honest, why defend him?

Where do Ms. Klingenberg’s loyalties lie: with the certified members, or with the homeowners? If the honest answer is with the certified members, then this is useful information for any consumer weighing the costs associated with a certified Passive House build.

As Martin Parker notes in a Guardian article regarding Business Schools and MBA Programs and their propensity to dismiss critics when things go horribly wrong in the economy, “That’s a tricky position, though, because, as a 2009 Economist editorial put it, ‘You cannot claim that your mission is to ‘educate the leaders who make a difference to the world’ and then wash your hands of your alumni when the difference they make is malign’.”

In addition, and rather pointedly, doesn’t Ms. Klingenberg’s response represent a dramatic failure of leadership? What should a person in a leadership role do when bad news comes their way: Confront it, work through it, and then move on? Ignore it? Or — worst option of all — should they try to bury it?

How can she (or Mr. Miller, for that matter) offer such flippant responses when someone else’s life savings are on the line? Do certified PHIUS members really believe this is an appropriate way to respond?

 

wikipedia.org Cheshire Cat

Illustration by Sir John Tenniel.

 

Furthermore, why are they so quick to take Brandon’s side? In the case of Mr. Miller, without even examining the evidence I was willing to offer. In Ms. Klingenberg’s case, is it because Brandon successfully achieved the Passive House standard on several projects? Doesn’t it matter how he achieved the standard? For example, you would think they might be interested in what Brandon’s previous clients have to say regarding their own experience building with him — e.g. pricing, timeline, job site conditions, the cost to build vs. an actual real estate valuation, etc.. Or does none of this matter?

More importantly, why not make customer satisfaction a component of the Passive House requirements? After all, what is the point of meeting all the stringent guidelines for Passive House certification if the result is a homeowner who feels beaten up by a design and build process that forces the conclusion that they have been financially exploited?

Does PHIUS only care about boxes and how they perform, or do they have a genuine interest in the people who live in them? If the answer is both, then why are they not actively evaluating the experience of homeowners along with the performance of the structures? How can a certified Passive House structure that contains an owner who is now cynical about the build process not be considered a failure?

 

Cup.410.g.74  55

Illustration by Sir John Tenniel.

 

Moreover, as an institution, does PHIUS have policies in place to censure, or otherwise hold to account, its certified members should they behave unethically or even criminally? If such policies exist, have they ever actually been enforced? Or, are we to believe all of their members are morally and ethically perfect?

For a certified PHIUS member who is in good standing, who treats people the right way, it would certainly be irksome to know Brandon and his team get to be listed next to them without even an asterisk to note the difference. Don’t certified members want there to be clear-cut guidelines regarding how architects, builders, and consultants should conduct themselves, and shouldn’t there be serious consequences for those who choose to contravene those guidelines?

 

“Nonprofit executives and board members also should be willing to ask uncomfortable questions: Not just ‘Is it legal?’ but also ‘Is it fair?’ ‘Is it honest?’ ‘Does it advance societal interests or pose unreasonable risks?’ and ‘How would it feel to defend the decision on the evening news?’ Not only do leaders need to ask those questions of themselves, they also need to invite unwelcome answers from others. To counter self-serving biases and organizational pressures, people in positions of power should actively solicit diverse perspectives and dissenting views. Every leader’s internal moral compass needs to be checked against external reference points.”

— Deborah L. Rhode & Amanda K. Packel

 

But then expecting even a modicum of objectivity from Mr. Miller, Ms. Klingenberg, or PHIUS was probably expecting too much:

2015 Passive House Projects Competition

2016 Passive House Projects Competition

Should the leader of an organization sit on a panel with other judges handing out awards to the organization’s members? It seems like this would be an excellent time to recuse oneself, if only to avoid even a hint of favoritism or undue bias. As a Law School Professor might frame it: ‘It’s not enough to be ethical, you need to avoid even the appearance of unethical behavior.

Yet, as a consumer, I’m expected to believe Ms. Klingenberg examined the evidence I sent her with an open mind, and that she reached an impartial determination as to what transpired between my family and EHB [?]. One wonders, did she even bother to contact any of Brandon’s former clients to ask about their experience building with Brandon and EHB? She didn’t take the time to sit down with us, or even ask us any questions via email, to establish whether we were just irrational cranks or if we had legitimate points to make. Apparently Brandon’s say-so that he had done nothing wrong was good enough for her.

It bears repeating what was at risk here: a family’s life savings. It’s also worth noting that it’s not enough for PHIUS to proclaim progressive values, those values should be reflected in the actions of individual members, as well as the actions and policies of the institution itself. Based on our own experience, we feel PHIUS is just one more institution that consumers and citizens cannot depend on to do the right thing when it matters most. But maybe to them this is all simply a case of: ‘it’s just business’.

It is undeniable that institutions have a nasty habit of closing ranks around their members, even the ones who clearly misbehave. If the member in question turns out to be a bad actor, however, then it is also true that this unquestionably reflects poorly on the institution’s integrity. Consider the recent history of the Chicago police department: Code of Silence  /  Laquan McDonald’s Shooting  /  Brutal History

What will Mr. Miller, Ms. Klingenberg, and PHIUS do as individuals and as an institution when this happens again (inevitably — when you consider the whole ‘leopard and his spots’ brand of folk wisdom)? Before protecting Brandon and EHB so forcefully, maybe they should make sure he is telling them the truth.

 

“If the existing order were a model order, and just and right in every respect, I naturally would have no objections to it. Since, however, it is a mixture of much that is good and much that is evil, unjust, and defective, to be called a friend of the existing order often is to be called a friend of what has outlived its usefulness and is principally evil. Progress is unceasing. Society is constantly changing. Institutions which at first suited the conditions under which they originated may become criminally unjust a half century later.”

— Johann Wolfgang von Goethe

 

commons.wikimedia.org

 

In light of the ever-quickening pace of our modern world, perhaps Goethe’s suggested timetable should be halved, in which case the Passive House concept is ripe for fundamental reform — going well beyond adjustments for climatic differences. History, it should be added, suggests those who currently hold positions of authority in the Passive House movement are unlikely to make the hard choices, or have the stomach to execute a meaningful overhaul.

For more details on how this all got started, check out these posts:

The Passive House Nightmare
“How Did I Get Here?…”